3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

Ten layered fidget discs off one plate - each about 3" across, each with its own cut-through pattern and its own way of spinning and clicking. Pick the design you want; the picture on each chip is that disc. Shown as a render, not a photo.

Design by PenguinPrototypes

A thin blade for digging the lint out of a phone's charging port, with a hook at one end and a flat scraper at the other. 34 mm long and a fraction of a gram, so it prints three at a time in a minute - one for the desk, one for the car, one to lose. Shown as a render, not a photo.

Design by eclien

Four bug cookie cutters with matching stamp inserts - cut the outline, press the details, bake. Each about 3" across, and the same set works for playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A flat key tag that holds the key by its bow rather than its ring, so it lies flat in a pocket and does not rattle. 2.2" long, about 1 g of plastic, printed in one piece. Shown as a render, not a photo.

Design by Katejot2017

A B2 in flying-wing form that sits on top of a joystick - the shape slots over the stem and pegs in, so it turns with the stick. 5.5" across the wings, printed in one piece plus two pegs. Shown as a render, not a photo.

Design by DeanPrinting

A small hook that sticks to a desk or a shelf edge with tape or a screw, for keys, headphones or a cable. 2.6" wide, printed in one piece with a flat back that sits flush. Shown as a render, not a photo.

Design by schiko

Eight bunny cookie cutters, each with a stamp insert - press the face and ears, cut the outline, bake. About 3" tall each, and the same set cuts playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A bow that clips onto a straw: the straw runs through the middle and the bow sits above the lid. Shown as a render, not a photo.

Design by Morganja

A hexagonal fidget that prints flat in a few minutes and clicks between your fingers - no supports, no assembly, no settings to tune. 2.0" across. Shown as a render, not a photo.

Design by LangHjornArt

A pill popper: drop a tablet in the cup, press the plunger and it crushes it under a lever instead of between two spoons. 4.2" long, printed in one piece, with a rounded base so it stands up. Shown as a render, not a photo.

Design by c4444

A heart that sits on top of a straw, wide and low, catching the light as the cup moves. Shown as a render, not a photo.

Design by Morganja

Seven traditional Christmas shapes, each about 3" across, printed with a cutting rim and a handle you can press. Cut a whole tin of mixed biscuits from one set. Shown as a render, not a photo.

Design by The_echoscapes

A clicker keychain with four buttons that press and click, printed in place so nothing needs assembling. Shown as a render, not a photo.

Design by Print3DFamilyFidgets

A fold-over bag clip in one piece, with nothing to assemble: two slim bars on a round hinge, and a hook at the far end that shuts them. Roll the bag's neck over, slide it in side-on between the bars, and press the hook home - the knob at the end of the curl rides over the upper bar's tip and drops into the groove cut behind it, so the clip is held shut by the hook and not by the moulding. Flex the curl back off the tip and it opens again. The hinge is a disc with a hole through it, so the clip hangs on a keyring or a cup hook when it is not on a bag. It prints flat as a single piece with no supports, and PLA holds fine while PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

A six-can holder that spins: six runners hold the cans and the base turns, and it uses very little filament for its size. Four pieces. Shown as a render, not a photo.

Design by JEP0405

A phone stand with a woodgrain surface that all but disappears behind the phone, so what you see is the screen standing on the desk rather than the stand holding it. A deep groove with a lipped front edge takes a phone upright for video calls or on its side for standBy and night-clock mode, and it fits anything from a small handset up to a Pro Max. Printed in PLA at 0.2 mm layers, 15% infill, no supports. It is designed for a wood-fill filament, which gives it the grain it is named for, though any matte colour prints just as well. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by M_LAB

Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

Two bands that print as one piece: the finned outer ring's ridge sits in the inner band's groove, so it is locked on but free to spin, with no bearings and nothing to assemble. The groove is a BALL RACE - a circular channel, with the ridge as the same circle held 0.4 mm off it - so the surfaces the two parts face each other across are vertical, which is what lets it print in place and still turn. The ring is 27 mm across and stands 7 mm, and the fins are trapezoids: wide where they join the sleeve, narrow at the tip, so nothing on it is a blade waiting to be knocked. It comes in three sizes, 16.5 mm (US 6), 18.2 mm (US 8) and 19.8 mm (US 10) across the finger hole, all at the same price, and the download is a 3MF with a plate for each, so you can print whichever fits - or all three. Print it with a brim and z-hop switched on: a small ring has a small footprint, and z-hop keeps a moving nozzle clear of what is already printed. The STL on its own is the smallest of the three. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A 3x3 clicker pad: nine keys on one printed body, each on its own spring, so the whole thing clicks under a thumb like a tiny keyboard. 2.6" square, printed in one piece with nothing to assemble. Shown as a render, not a photo.

Design by Print3DFamilyFidgets

A bag peg that works like a clothes peg: two arms on a printed pin, so the ends you squeeze and the jaws are on opposite sides of the pivot, and squeezing opens the jaws. A disc on the upper arm turns inside a socket on the lower one, printed in place with a quarter of a millimetre of air round it - press the peg open and you can feel the pin move. Behind it one strip sweeps round and back to the other arm as a scroll you can see through, and that scroll is the spring: it closes the jaws and it is what you feel working when you squeeze. The mouth is a square-wave channel cut through both jaws at once, so the two sets of teeth come from the same cut and interlock - every tooth of one jaw stands in the hollow of the other - and along the outside of each arm, where a thumb goes, a row of sawteeth bites into the silhouette so the peg does not slip in your hand. It prints flat as one piece, no supports, nothing to assemble. PLA holds fine; PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

A star that spins: the points are cut so it turns on its axis in the hand and keeps turning. Shown as a render, not a photo.

Design by CreaitivityStudio

A snake, printed flat as one piece: 9.8" from nose to tail, no supports anywhere, and off the plate in about an hour by its designer's own estimate. It prints lying on the plate, so the whole thing is one layer stack rather than a tower that can topple. Shown as a render, not a photo.

Design by user_3738174853

A chef's hat charm with a banded brim, tall enough to read at a glance on a keyring. Shown as a render, not a photo.

Design by Tim

A textured clicker with a body and a set of button caps: the caps press into the body and click under a thumb, and the spare sizes in the set let you choose how stiff it feels. 2.6" long, printed in one go. Shown as a render, not a photo.

Design by ArmadilloFDM

A cactus that clicks: the body snaps onto a keyboard switch, so the whole cactus is the button and the click comes from the switch inside it. Four designs, sold one at a time - pick the cactus you want, about 1.3" tall, and it prints in two pieces that snap together without glue. Shown as a render, not a photo.

Design by UKSTL

A pencil that bends: the barrel is printed as a chain of flexing segments, so it folds in your hand and springs straight again, and it still looks like a pencil with a point at one end. 4.8" long, printed in one piece. Shown as a render, not a photo.

Design by TinkerTogether

A plain fidget spinner with no ornament on it at all: a body, three arms and a bearing seat in the middle. Five sizes come off the one plate, from a 1.6" one that fits in a pocket up to a 2.7" one, and the plate also carries the grips that go in the bearing seat. Pick the size you want - each is printed as one piece. Shown as a render, not a photo.

Design by MakerShed

A hook that hangs over the top of a door - no screws, no drilling, nothing to fix to the wall. 2.7" wide and 4.3" tall, about 13 g of plastic. Shown as a render of the printable model, not a photograph.

Design by blunt

Two clickers that look like lunch: a bao bun with its pleats, and half an avocado with the stone still in. Each is two printed halves that snap together over a switch, so the whole thing is the button. Pick the one you want - about 1.8" across. Shown as a render, not a photo.

Design by iNkosi3D

A fridge egg dispenser: eggs roll down a ramp and out of the front one at a time, so the oldest is always the next to come out. 9.7" long and holds a dozen, printed in three pieces - the ramp, the body and the front cup - with no supports. Shown as a render, not a photo.

Design by specialman

A kitchen roll holder with a weighted base: the disc takes sand or coins, so the roll stays put while you pull one sheet off with one hand. 9.1" tall, printed as a base and a post. Shown as a render, not a photo.

Design by MicahW3D

A holder that stands cutlery up in a drawer or on a counter, with slots for forks, knives and spoons and a low front so you can see what you are reaching for. 5.9" long, printed in one piece. Shown as a render, not a photo.

Design by Alex

A print-in-place bag clip: the hinge prints shut and then works, so there are no pins and nothing to assemble. 3.2" long, 1.2" wide. Shown as a render of the printable model, not a photograph.

Design by printerforge

An upright organizer for the utensils that live on the counter: compartments of different heights, a flat back to go against a wall, and a base wide enough that a ladle does not tip it. 8" long, printed in one piece. Shown as a render, not a photo.

Design by lunatiic

Four Halloween cutters - pumpkin, ghost, bat and the like - about 3" across each, printed with a cutting rim deep enough for biscuit dough or Play-Doh. One plate prints the set. Shown as a render, not a photo.

Design by Creaitivity Studio

A rest for a wooden spoon: the bowl sits in the cradle and the handle lies over the rim, so the drips land in the holder instead of the hob. 4.7" across, printed in one piece. Shown as a render, not a photo.

Design by Jirka108

A shelf that hangs under a shelf: it clips over the front edge of an existing board and gives you a second tier in the gap, for mugs, spice jars or a router. 6.9" wide, printed in one piece. Shown as a render, not a photo.

Design by PanteraRuber

Four wedding cutters with stamp inserts - the ring, the cake slice and two more - for biscuits at an engagement or a hen do. About 3" across each, and the same set cuts playdough for the small guests. Shown as a render, not a photo.

Design by Merilno3D

A flat page marker with a fox carved in raised relief across its face - it slides over the page and the design reads against the paper. 9.4" long and 2.7 mm thin, printed flat in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by shadow.lune

A flat organizer that divides a kitchen drawer into compartments - it lies 2 mm deep, so it adds dividers without eating the depth of the drawer. 9.6" across, printed flat in one piece. Shown as a render, not a photo.

Design by Nix3D

A bench holder that keeps dental drill bits upright, sorted and off the tray. 3.3" x 2.2" x 0.8", about 30 g of plastic. Shown as a render of the printable model, not a photograph.

Design by pain.killer.2

A desk golf set in eleven printed pieces: a green you can rearrange piece by piece, a ball, a club and the furniture around it. About 3" a piece and 115 g of plastic for the set. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by SakiSale

A flat floral bookmark: one thin spray of three openwork blossoms and leaves that lies between the pages and reads against the paper, marking the page without thickening the book. 5.9 x 4.4" overall and 1.6 mm thin, printed flat in one piece in a few minutes. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Rankhispano

A mini golf hole for the desk: a printed course board with the hole and a rock surround, a club and a ball, all printed flat. 8.7" x 7.2", about 62 g of plastic for the set. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by MoltenPlastic3D

A bookmark of a book with a coffee cup resting on the stack - flat, 3.7" tall, and thin enough that it does not mark the pages. Printed in one piece in about a minute. Shown as a render, not a photo.

Design by giessener

A bookmark shaped like an alligator, with the jaw clipping over the page and the body lying in the gutter - so it marks the page and the line at once. 3.9" long, printed as a body and a jaw. Shown as a render, not a photo.

Design by 3dprinting

A little hand that clips onto the page and points at the exact line you stopped on - so a bookmark marks where you are, not just which page. 2.8" long, printed flat with the fingers already free. Shown as a render, not a photo.

Design by helder.bernardo

A pencil cup wrapped in overlapping scales, so it reads as a little pinecone on the desk while holding a fistful of coloured pencils. 3.3" across and 3.1" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by impresionao