$1.75Was $2.58
A hook that hangs over the top of a door - no screws, no drilling, nothing to fix to the wall. 2.7" wide and 4.3" tall, about 13 g of plastic. Shown as a render of the printable model, not a photograph.
Design by blunt
$17.55Was $26.00
A shelf that hangs under a shelf: it clips over the front edge of an existing board and gives you a second tier in the gap, for mugs, spice jars or a router. 6.9" wide, printed in one piece. Shown as a render, not a photo.
Design by PanteraRuber
$10.71Was $15.86
A napkin holder with an open frame: a stack of serviettes sits in the base and the side wall holds them upright, so you can take one without the rest following. 6.3" long, printed in one piece. Shown as a render, not a photo.
Design by Jyffen
$3.38Was $5.00
A flat page marker with a fox carved in raised relief across its face - it slides over the page and the design reads against the paper. 9.4" long and 2.7 mm thin, printed flat in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by shadow.lune
$8.80Was $13.04
Eight napkin rings shaped like sea creatures - starfish, shells and fish - each holding a folded napkin on its side. About 3" across, printed flat in one colour or several. Shown as a render, not a photo.
Design by adnamantino
$4.10Was $6.06
A bench holder that keeps dental drill bits upright, sorted and off the tray. 3.3" x 2.2" x 0.8", about 30 g of plastic. Shown as a render of the printable model, not a photograph.
Design by pain.killer.2
$15.58Was $23.08
A desk golf set in eleven printed pieces: a green you can rearrange piece by piece, a ball, a club and the furniture around it. About 3" a piece and 115 g of plastic for the set. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by SakiSale
$1.34Was $1.99
A flat floral bookmark: one thin spray of three openwork blossoms and leaves that lies between the pages and reads against the paper, marking the page without thickening the book. 5.9 x 4.4" overall and 1.6 mm thin, printed flat in one piece in a few minutes. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by Rankhispano
$8.36Was $12.38
A mini golf hole for the desk: a printed course board with the hole and a rock surround, a club and a ball, all printed flat. 8.7" x 7.2", about 62 g of plastic for the set. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by MoltenPlastic3D
$1.34Was $1.99
A bookmark of a book with a coffee cup resting on the stack - flat, 3.7" tall, and thin enough that it does not mark the pages. Printed in one piece in about a minute. Shown as a render, not a photo.
Design by giessener
$1.34Was $1.99
A bookmark shaped like an alligator, with the jaw clipping over the page and the body lying in the gutter - so it marks the page and the line at once. 3.9" long, printed as a body and a jaw. Shown as a render, not a photo.
Design by 3dprinting
$1.34Was $1.99
A little hand that clips onto the page and points at the exact line you stopped on - so a bookmark marks where you are, not just which page. 2.8" long, printed flat with the fingers already free. Shown as a render, not a photo.
Design by helder.bernardo
$7.59Was $11.24
A pencil cup wrapped in overlapping scales, so it reads as a little pinecone on the desk while holding a fistful of coloured pencils. 3.3" across and 3.1" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.
Design by impresionao