3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A corgi that keeps the bread shut: the body is the clip, the ears are the handle and it sits on the bag like a peg. 5.4" long, printed in place in one piece. Shown as a render, not a photo.

Design by Burak19891

A gripper that clips two chopsticks together into one easy pair - for a child learning, or anyone who has given up on holding two sticks. 1.4" across, printed in one piece, and the large and small blanks are on file for different stick thicknesses. Shown as a render, not a photo.

Design by RynoRC

Four bee-and-honeycomb cutters with stamp inserts - the bee, the flower and two honeycomb shapes. Press the stamp for the detail, cut the outline, bake; each is about 3" across. Shown as a render, not a photo.

Design by Merilno3D

Two holders that keep takeaway lids upright and sorted instead of sliding about in a drawer - one for the small lids, one for the large. 6.8" and 4.8" tall, printed as a pair; the designer measured them for Tesco containers. Shown as a render, not a photo.

Design by FaasteerCZ

A Santa in his sleigh for the corner of a door frame: the sleigh runs behind him as a counterweight, so the piece sits up on its own along the top corner of a door or a window. The designer's updated file carries both the left-hand and the right-hand version, so the pair is what is printed. Designed by lindnjoe and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by lindnjoe

An ornament that hooks over the corner of a door frame: a bauble hanging from a bow on the trim above a door, flat on the back so it sits square in the corner. Sold as one corner piece, 196 by 207 mm. Designed by lindnjoe and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by lindnjoe

A little town under snow that prints as one piece: rooftops, houses and trees drifting into each other, with holes modelled through the houses so a micro LED string can be threaded in and the windows light from inside. This is the designer's fixed-roof version, and davidkelly021 publishes a separate base for it with room for a battery pack. Printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by davidkelly021

The words Merry Christmas in a flowing script, arranged in the shape of a Christmas tree: a star at the top and the swashes of the letters curling out into the branches. The line work is all joined into one flat piece, so it prints as a single item and hangs flat on a wall or a door. Designed by OrangeSs and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by OrangeSs

A rose for the top of a 40 oz Stanley cup lid: the bloom prints standing up on the topper, so a plain cup gets a flower on it with nothing to glue in place. It fits the 40 oz lid. Designed by speedster, who remixed Picture_it's blank Stanley lid topper - both makers are credited on this page and both licences are recorded beside the file. Printed under Creative Commons Attribution 4.0 (CC BY 4.0); the topper it is built on is CC BY-SA 4.0, and the print is sold unaltered. Shown as a render of the printable model, not a photograph.

Design by speedster

Five draped ghosts, each with cut eyes and a mouth and each hollow underneath, so it sits over a battery LED tealight and glows from the inside with the light showing through the cutouts. They print as five separate pieces at slightly different sizes, so they can be scattered along a table, a shelf or a porch step - the set is all five. An LED tealight only, as the designer intends: a real flame would soften the plastic. Designed by kappern and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by kappern

A blank topper that sits on a 40 oz Stanley cup lid, flat and smooth, so it is a base for whatever goes on top: the designer's own page explains how to add text to it in Bambu Studio, choosing the font and the size and then the colour of the topper and of the writing separately. Sold blank, exactly as published. Designed by Picture_it and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Picture_it

A ten-point star for the top of a Christmas tree. The plate carries two star faces with a mount and two pegs, so the star goes together without glue. Designed by hyperZ and printed under Creative Commons Public Domain, so it is free of conditions. Shown as a render of the printable model, not a photograph.

Design by hyperZ

A snowflake cut to sit over the top corner of a door frame, so the corner of a door is dressed for the season. It prints flat and reads well in one colour or in several - the designer's own photos show both. Designed by lindnjoe and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by lindnjoe

Five Christmas tree ornaments on one plate: small shapes around 60 mm tall to hang from the branches, printed flat and thin so they sit light on a tree. Sold as the set of five. Designed by OrangeSs and printed under Creative Commons Public Domain, so it is free of conditions. Shown as a render of the printable model, not a photograph.

Design by OrangeSs

A three-piece standing sign: the words Merry Christmas in script, a pair of snowflakes, and the solid block that both plates slot into. The base carries most of the weight, so the sign stands on a mantel or a windowsill without tipping, and the whole thing goes together without glue. Sold as the three printed pieces. Designed by lindnjoe and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by lindnjoe

A door corner for Halloween: a cat with a knife, cut to sit over the corner of a doorframe and be read from across the room. 7.9 by 7.8 inches and 5 mm thick, it prints flat in about an hour with no supports, and a 0.6 mm nozzle is an option the designer mentions for a chunkier line. Designed by H & R 3D and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by H & R 3D

A corner piece for the trim above a door: a small Christmas scene that sits in the corner of the frame, printed in one colour or several, so the tree and the snowman can each take their own filament. Two files, left and right, because the corner decides which way it faces. Designed by lindnjoe and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by lindnjoe

A small ghost holding a tealight: the flame glows through the shell and out of the eyes, so the whole figure lights up. 3" tall, about 12 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A candy machine that turns a canning jar into a dispenser: a base that screws onto the jar's own lid ring, a knob and a printed pin, so no screw is needed anywhere. Fill the jar with sweets, fit the base, turn the knob and a few drop through. The designer also ships a stronger pin for silk PLA, and a second file for the narrower Hema store jar. Designed by carlbelcher and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by carlbelcher

Two bats for the corner of a door frame at Halloween: one running along the top of the frame and a second spreading over the join. The pieces snap together - a little glue if a joint is loose - and a strip of tape on the back holds it where a frame is not square, which the designer added because his was not and says it is optional. Designed by jdicerchio and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by jdicerchio

A Christmas tree built from organic, irregular tiers rather than a cone - the branches spiral and overhang, so it looks grown instead of drawn. Two sizes, 4" and 6" tall, each printed in one piece. Shown as a render, not a photo.

Design by 3dinsidegr

A ribbon Christmas tree with a bow: flat loops folded into a tree shape, with a hole at the top to hang it. 3.9" tall, about 6 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Ababskia3D

A Christmas teddy bear: a bear in a Santa hat with a ribbon to hang it by, printed in two sizes. 2" or 3.1" tall, about 12 g and 40 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by raven.log

A snowman in two printed pieces: a body with print-in-place joints for the arms, and a head that hangs on its own link so it swings independently as the earring moves. Each is about 30 mm tall, prints flat with no supports, and a pair is two snowmen. Shown as a render of the printable model, not a photograph.

Design by tomo3D

Winter forest deer ornaments: three deer among trees, cut as flat silhouettes with a hole to hang each one. 3.4" each, about 21 g of plastic for the set of three. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Walter3D

A rack that stands petri dishes upright to drain or to sit on a shelf. 2.9" x 4.5" x 2.5". Shown as a render of the printable model, not a photograph.

Design by Clément Vasseneix

A rack that holds laboratory test tubes upside down so they drain and dry: 185 mm x 110 mm x 75 mm. Shown as a render of the printable model, not a photograph.

Design by jakub.fousek97

A print-in-place bag clip: the hinge prints shut and then works, so there are no pins and nothing to assemble. 3.2" long, 1.2" wide. Shown as a render of the printable model, not a photograph.

Design by printerforge

A round spider web in a ring, with every strand cut through so the web is open and a spider sits in the middle of it. Each is about 44 x 48 mm and 2.2 mm thick, with a loop at the top for a hook, and both webs print together as one piece. Shown as a render of the printable model, not a photograph.

Design by tomo3D

Two layered Christmas trees, 33 mm tall, each with a loop at the top for a hook - a few flat layers stacked into a tree, so they read as a tree from the front and none of it is a support to remove. Designed by instintkiller and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by instintkiller

Two hexagonal mesh pockets angled into each other, so a pair of shoes sits heel-down without one resting on the other. 220 mm wide, 165 mm tall and 130 mm deep, printed as one piece. Remixed by ThatGuy123568 from jordi_id7's original Shoe organizer on Thingiverse. Shown as a render of the printable model, not a photograph.

Design by ThatGuy123568

Two clickers that look like lunch: a bao bun with its pleats, and half an avocado with the stone still in. Each is two printed halves that snap together over a switch, so the whole thing is the button. Pick the one you want - about 1.8" across. Shown as a render, not a photo.

Design by iNkosi3D

A glasses rack that lives on the wall: six cradles in a row on one 210 mm plate, 22 mm deep, so six pairs hang out of the way of a counter or a bedside table. It prints as one piece with nothing to assemble, and the arms take wire or plastic frames by the bridge. Designed by Matthew and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Matthew

A chef's hat charm with a banded brim, tall enough to read at a glance on a keyring. Shown as a render, not a photo.

Design by Tim

A bag peg that works like a clothes peg: two arms on a printed pin, so the ends you squeeze and the jaws are on opposite sides of the pivot, and squeezing opens the jaws. A disc on the upper arm turns inside a socket on the lower one, printed in place with a quarter of a millimetre of air round it - press the peg open and you can feel the pin move. Behind it one strip sweeps round and back to the other arm as a scroll you can see through, and that scroll is the spring: it closes the jaws and it is what you feel working when you squeeze. The mouth is a square-wave channel cut through both jaws at once, so the two sets of teeth come from the same cut and interlock - every tooth of one jaw stands in the hollow of the other - and along the outside of each arm, where a thumb goes, a row of sawteeth bites into the silhouette so the peg does not slip in your hand. It prints flat as one piece, no supports, nothing to assemble. PLA holds fine; PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

A heart that sits on top of a straw, wide and low, catching the light as the cup moves. Shown as a render, not a photo.

Design by Morganja

A bow that clips onto a straw: the straw runs through the middle and the bow sits above the lid. Shown as a render, not a photo.

Design by Morganja

Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A six-can holder that spins: six runners hold the cans and the base turns, and it uses very little filament for its size. Four pieces. Shown as a render, not a photo.

Design by JEP0405

A fold-over bag clip in one piece, with nothing to assemble: two slim bars on a round hinge, and a hook at the far end that shuts them. Roll the bag's neck over, slide it in side-on between the bars, and press the hook home - the knob at the end of the curl rides over the upper bar's tip and drops into the groove cut behind it, so the clip is held shut by the hook and not by the moulding. Flex the curl back off the tip and it opens again. The hinge is a disc with a hole through it, so the clip hangs on a keyring or a cup hook when it is not on a bag. It prints flat as a single piece with no supports, and PLA holds fine while PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

A 608 bearing that prints already assembled - the races, the balls and the cage all come off the plate as one piece, and it turns as soon as you break it free. 22 mm across, 7 mm thick, the size a fidget spinner or a skate wheel takes. Shown as a render, not a photo.

Design by Jerryie

A hose clamp you print instead of buying: a ring with a screw lug that tightens onto a hose or a duct. Four sizes, measured across the clamp - 33 mm, 40 mm, 60 mm and 88 mm - each printed in one piece. Shown as a render, not a photo.

Design by inhabitworker

A bag clip shaped like a cat, with a spring jaw that holds a chip bag or a coffee pouch shut. 1.6" across, printed in place in one piece - the hinge comes off the plate already working. Shown as a render, not a photo.

Design by Muuurt

A bit holder that clips to a Ryobi ONE+ battery: the mount takes the loose bits you are using and keeps them on the drill, so they travel with the tool rather than in a pocket. 2.1" long, printed in one piece. Shown as a render, not a photo.

Design by Terrain 6

A cap that turns a jar into a fruit washer: fill it, shake, and the water spins the berries clean instead of bruising them. The cap and its inner piece print together in one go - size L fits a standard wide jar. Shown as a render, not a photo.

Design by ValeraPerinski

A workshop set of ISO 4017 hex-head screws in M3, M4, M5, M6, M7, M8 and M10, each size on its own plate, so you print the sizes you need and keep a jar of spares. The whole set is seven plates and about 55 g of plastic; the M10 is 2.8" long. Shown as a render, not a photo.

Design by Jerryie

A Christmas cookie stamp and its matching cutter: press the stamp into the dough and the outline cuts clean around it, so the icing has a line to follow. 3.1" across, printed as two pieces - stamp and cutter. Shown as a render, not a photo.

Design by P2T

Shims for levelling a cabinet, packing a hinge or shimming a door frame. One plate is four shims - 42 x 89 mm, one each at 1 mm, 2 mm, 3 mm and 5 mm thick - so you pick the thickness that squares the job up instead of stacking paper. Shown as a render, not a photo.

Design by 3dprinting