3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

Two sharpened pencils, 42 mm long and 11 mm across, with the point cut so the graphite reads as a separate tip - about 0.2 g of plastic each, which is light enough to forget they are on. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by Tinker Together. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Tinker Together

Plant labels for a garden that gets replanted: the designer built them parametric, so the size, the shape and the lettering can all be cut to suit a bed, and each label takes only a few grams of filament even with a colour change. Store-bought labels fade and crack in a season; these do neither, and they read from the far end of the row. This listing is the designer's own set of shapes as they come, about five inches tall. Designed by Cullen J Webb and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Cullen J Webb

A kicking tee for rugby: a 120 mm base with a stem that stands the ball at the angle a kicker wants, so a conversion or a kick-off starts from the same place every time. 110 mm deep and 72 mm tall, printed as one piece with a wide foot that will not skate on wet grass. Designed by dhs and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by dhs

One continuous line draws a face in profile, cut out flat as an earring: 26 mm tall, 2 mm thick, with a hole at the top for a hook. Sold as a pair, mirrored so the two faces look at each other. Shown as a render of the printable model, not a photograph.

Design by Margen3d

A hot air balloon with its gores moulded in, the netting raised and a basket hanging under it on two lines, printed 1.9 mm thick. Each is 30 x 50 mm with a hole at the top of the envelope for a hook, and the pair prints together. Shown as a render of the printable model, not a photograph.

Design by ProtoEngineering

Eight citrus halves on one plate - orange, lime and lemon - each a 35 mm slice with a hole for a hook, so the set is four pairs or a bowl of citrus to rearrange. Printed flat in PLA with no supports and no colour changes: the segments are geometry, not paint. Designed by jdicerchio and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0); the parts are sold unaltered and this listing is offered under the same licence. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by jdicerchio

A peg that holds a blanket down: the stem goes into sand or soft ground and the arm clamps the corner, so a windy afternoon does not take the picnic with it. Print in PLA or PETG, no supports; five come off one plate, about eight inches square. Designed by Ainon3Dprint and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Ainon3Dprint

A practice mute for trombone, printed in three parts: the long tapered body that goes down into the bell, the flared cup that caps it, and the small collar that keeps the two together. 250 mm long and 193 mm across the cup, so it takes a full-size bell. The cup is what does the muting, so the horn can be played in an apartment without the neighbours learning the set list. Designed by 烤肉大师 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by 烤肉大师

A mirrored flourish - a curling stem with leaf-shaped tips - cut 2 mm thick, each about 24 x 36 mm with a hole at the end of the stem for a hook. The pair prints flat as one piece and lies along the ear rather than hanging off it. Shown as a render of the printable model, not a photograph.

Design by Vulcain

A ribbon of open spirals, 60 mm long and 25 mm across, printed upright so the turns come off the plate as clean as they look - nothing to sand between them. One earring fills the plate, so a pair is printed twice. Designed by Mike Olszak and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Mike Olszak

A paw print with four toe pads and a deep heel pad, cut 2.3 mm thick so the pads stay proud of the outline instead of blurring into it. Each paw is 23 x 24.5 mm with a hole between the toes for a hook, and the pair is mirrored so the prints face the same way when they are worn. Shown as a render of the printable model, not a photograph.

Design by Slowpoke’s Workshop

A lid that presses onto an open drinks can and slides shut, keeping dust, wasps and debris out of a beer or a soda between sips. Two fits are on offer: the standard can, whose lid measures 1.4 by 1.9 inches, and a wider one at 1.5 by 2.4 inches for a fatter 16 oz rim. Each prints as a lid and its sliding cover, and the standard lid also comes in the designer's looser-fitting version for a can that runs tight. Designed by Tiger prints, who remixed EcoDad's Printables lid - both makers are credited on this page - and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Tiger prints

Four plectrum shapes, two of each, printed flat as one sheet: a teardrop, a jazz point, a wide triangle and a rounded standard, at 1.0 and 1.4 mm so a player can find the thickness they like without buying four packs. Each pick is about 34 mm long and the texture on the back of the thicker ones keeps a sweaty thumb where it belongs. Designed by SF3DPrints and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by SF3DPrints

A pair of sunglasses with the arms and a bridge moulded in, printed 2.5 mm thick and 32 mm across, with a hole in each arm for a hook. They are a joke that prints properly: the lenses are open, so the shape holds at this size and reads at a glance. Shown as a render of the printable model, not a photograph.

Design by tomo3D

Two filigree horse heads, 45 mm by 28 mm and 2.5 mm thick, cut into openwork so they stay light enough to wear all day - about a gram and a half of plastic each. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by C4UStudio. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by C4UStudio

A can cap that opens the can as well: press it over the top of a standard 355 ml tab can and the drink is covered between sips, with the opener moulded into the same part. It prints in one piece in about forty minutes with no supports. Designed by BUD THE RETIRED PRINT GUY and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by BUD THE RETIRED PRINT GUY

A filigree arch: a curved band of scrollwork with the spaces cut right through, so it reads as lace from the front and sits like a crescent against the ear. Each is 26 x 34 mm and 2.3 mm thick with the hook tab at the top, and the pair is mirrored. Shown as a render of the printable model, not a photograph.

Design by Vulcain

A fidget cross charm whose arms spin in place, with the ring hole printed at the top for a chain or a split ring. Four sizes, 1.8" to 2.5" tall. Shown as a render of the printable model, not a photograph.

Design by BlackSheepStudio

A hook keeper that clips onto the rod handle and gives a lure somewhere to sit between casts, instead of swinging at the line. Three sizes, for rod handles of three diameters; the designer prints his in PETG and that is what the shop prints here, since this is a part that goes to the water. Designed by bambaxp and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by bambaxp

A pick holder with four feet that stands on an amp or a desk: slanted slots take plectrums by the tip so they can be pulled out one at a time, and the block is 90 mm long, 28 mm wide and 12 mm tall. The slots are cut at an angle, which is what stops a pick sliding back down into the holder. Designed by gareth7562 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by gareth7562

Two flip flops printed as one piece, each with a raised strap and a toe post standing up through the sole, so they read as sandals rather than flat outlines. Each is about 30 mm long with a hole at the heel for a hook, and the pair comes off the plate together. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A headband with a horn and two ears, 205 mm across and 6 mm thick, so it sits flat on the head and prints in one piece on the plate with nothing to glue. The band is a loop rather than a rigid arc, so it grips a child's head and an adult's. Designed by Jakub Lattenberg and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Jakub Lattenberg

A santa hat with the tip curling over: the brim is a raised band, the crown is domed and the tip hangs past the brim, so the shape reads from the side as well as the front. Each hat is 23.8 x 15.3 mm and 5.5 mm tall with a hole through the crown for a hook, and the plate prints six of them, which is three pairs. Shown as a render of the printable model, not a photograph.

Design by Ettore

Labels for a kitchen garden: eleven vegetables and herbs - aubergine, basil, pumpkin, corn, parsley, leek, beetroot, chives, sunflower, spinach and zucchini - cut in relief so the word reads from the path and a season outside does not wear it away. Print at 0.2 mm with no supports. Each sign is about six inches wide on its own stake. Designed by Schenk and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Schenk

A headband in a soft wave, 157 mm across and printed in PETG the way its designer publishes it - PETG bends where PLA would snap, and a headband is a part that gets flexed every time it is worn. Designed by Elyse_ and released as Creative Commons Public Domain (CC0 1.0), so the prints may be sold with no condition attached. Shown as a render of the printable model, not a photograph.

Design by Elyse_

Bauble hooks printed as a snap-off blister: a flat frame of S-hooks joined by 0.4 mm bridges, so you snap off as many as you need with your fingers and the rest stay in the frame, in the box, untangled. A couple of minutes of printing replaces the annual fight with a ball of wire hooks. The frame is about 5.3 by 1.7 inches and weighs 3 grams. Designed by mixardstudio.pl and printed under Creative Commons Public Domain (CC0 1.0). Shown as a render of the printable model, not a photograph.

Design by mixardstudio.pl

An abstract crucifix: the figure flows into the cross in one smooth line, pared down to the gesture rather than the detail. Three sizes in the one design family, 9.8", 9.3" and 8.6" at their longest - each sold on its own. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by 3dKingpin

A race medal with a moulded ribbon and a numbered disc in the middle. The file holds first, second and third, so a set covers a whole podium for a school race or a party game. The picture is a render of the printable model, not a photograph of a finished print.

Design by Rodrigo Ferriz

A cross worn as a keychain: Jesus on the front, JESUS down the beam, and a molded loop at the top for a split ring. 3.9" tall and 2.4" across the arms, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Christ Art

A bee feeder for the garden: a shallow dish with a landing grid so bees can drink without drowning in it. Fill it with sugar water and hang it or set it among the flowers. The picture is a render of the printable model, not a photograph of a finished print.

Design by DanyP86

A flat floral bookmark: one thin spray of three openwork blossoms and leaves that lies between the pages and reads against the paper, marking the page without thickening the book. 5.9 x 4.4" overall and 1.6 mm thin, printed flat in one piece in a few minutes. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Rankhispano

A crowned lion head with a loop at the top, about four inches tall - a pendant, a bag charm or a wall ornament, with the mane and crown cut deep enough to hold a highlight. One piece. The picture is a render of the printable model, not a photograph of a finished print.

Design by digidihey

A bookmark of a book with a coffee cup resting on the stack - flat, 3.7" tall, and thin enough that it does not mark the pages. Printed in one piece in about a minute. Shown as a render, not a photo.

Design by giessener

A pencil cup wrapped in overlapping scales, so it reads as a little pinecone on the desk while holding a fistful of coloured pencils. 3.3" across and 3.1" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by impresionao

A 608 bearing that prints already assembled - the races, the balls and the cage all come off the plate as one piece, and it turns as soon as you break it free. 22 mm across, 7 mm thick, the size a fidget spinner or a skate wheel takes. Shown as a render, not a photo.

Design by Jerryie

A keyring that opens without a metal split ring, printed as one piece with nothing to assemble. The flat band is broken once, and across that break the two ends lap through the ring's own thickness - the socket keeps the lower half, the near end the upper, with a quarter of a millimetre of air between them - so the finished ring reads as one band with a hairline in it rather than two pieces butted together. What holds it shut is the gate's own end, narrowed to a tongue: the band's inner and outer edges step down either side of it, and the tongue carries a rounded bump underneath that sits in a seat cut into the socket. Flex the ring apart and the bump rides up its own rounded side, which is a detent and not friction; let go and it drops back in. The tongue is relieved with a round hole at its root, because that is where it bends when you press it up to open the ring. Flex it, thread your keys on, squeeze it shut. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

A workshop set of ISO 4017 hex-head screws in M3, M4, M5, M6, M7, M8 and M10, each size on its own plate, so you print the sizes you need and keep a jar of spares. The whole set is seven plates and about 55 g of plastic; the M10 is 2.8" long. Shown as a render, not a photo.

Design by Jerryie

A graduation cap and gown on a keyring: the mortarboard tilted over the gown, with a class year or a name across the front on the version the designer included for it. It hangs flat and reads clearly from a distance, which is what a keepsake for a graduate wants to do. Printed as one tag with the layered faces so the cap, the gown and the lettering each read separately. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Cardboard Junkie

A pair of thin earrings, each 1.4" x 1.6" and about 2 mm thick, so they print as one small plate in a couple of minutes and weigh almost nothing on your ears. The pair is one item - the price is for both. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render, not a photo.

Design by Vulcain

Five heart shapes, each layered front to back so the colours read as depth: black sits at the back as the outline and the two layers in front are yours to choose, so one colour is the simplest and three makes it pop. Pick the shape you want - each is about 1.6" by 1.5", with a loop for a keyring or a chain. Shown as a render, not a photo.

Design by dominator334

Two bands that print as one piece: the finned outer ring's ridge sits in the inner band's groove, so it is locked on but free to spin, with no bearings and nothing to assemble. The groove is a BALL RACE - a circular channel, with the ridge as the same circle held 0.4 mm off it - so the surfaces the two parts face each other across are vertical, which is what lets it print in place and still turn. The ring is 27 mm across and stands 7 mm, and the fins are trapezoids: wide where they join the sleeve, narrow at the tip, so nothing on it is a blade waiting to be knocked. It comes in three sizes, 16.5 mm (US 6), 18.2 mm (US 8) and 19.8 mm (US 10) across the finger hole, all at the same price, and the download is a 3MF with a plate for each, so you can print whichever fits - or all three. Print it with a brim and z-hop switched on: a small ring has a small footprint, and z-hop keeps a moving nozzle clear of what is already printed. The STL on its own is the smallest of the three. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A bag peg that works like a clothes peg: two arms on a printed pin, so the ends you squeeze and the jaws are on opposite sides of the pivot, and squeezing opens the jaws. A disc on the upper arm turns inside a socket on the lower one, printed in place with a quarter of a millimetre of air round it - press the peg open and you can feel the pin move. Behind it one strip sweeps round and back to the other arm as a scroll you can see through, and that scroll is the spring: it closes the jaws and it is what you feel working when you squeeze. The mouth is a square-wave channel cut through both jaws at once, so the two sets of teeth come from the same cut and interlock - every tooth of one jaw stands in the hollow of the other - and along the outside of each arm, where a thumb goes, a row of sawteeth bites into the silhouette so the peg does not slip in your hand. It prints flat as one piece, no supports, nothing to assemble. PLA holds fine; PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

A fold-over bag clip in one piece, with nothing to assemble: two slim bars on a round hinge, and a hook at the far end that shuts them. Roll the bag's neck over, slide it in side-on between the bars, and press the hook home - the knob at the end of the curl rides over the upper bar's tip and drops into the groove cut behind it, so the clip is held shut by the hook and not by the moulding. Flex the curl back off the tip and it opens again. The hinge is a disc with a hole through it, so the clip hangs on a keyring or a cup hook when it is not on a bag. It prints flat as a single piece with no supports, and PLA holds fine while PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

A phone stand with a woodgrain surface that all but disappears behind the phone, so what you see is the screen standing on the desk rather than the stand holding it. A deep groove with a lipped front edge takes a phone upright for video calls or on its side for standBy and night-clock mode, and it fits anything from a small handset up to a Pro Max. Printed in PLA at 0.2 mm layers, 15% infill, no supports. It is designed for a wood-fill filament, which gives it the grain it is named for, though any matte colour prints just as well. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by M_LAB

Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A short sword bookmark with its own sheath: the blade marks your page and the scabbard clips back over it. 5.7" long, printed flat, the two pieces together weighing about 8 g. Shown as a render of the printable model, not a photograph.

Design by Forged in Filament

A rack that stands petri dishes upright to drain or to sit on a shelf. 2.9" x 4.5" x 2.5". Shown as a render of the printable model, not a photograph.

Design by Clément Vasseneix

Two layered Christmas trees, 33 mm tall, each with a loop at the top for a hook - a few flat layers stacked into a tree, so they read as a tree from the front and none of it is a support to remove. Designed by instintkiller and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by instintkiller