3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

Four plectrum shapes, two of each, printed flat as one sheet: a teardrop, a jazz point, a wide triangle and a rounded standard, at 1.0 and 1.4 mm so a player can find the thickness they like without buying four packs. Each pick is about 34 mm long and the texture on the back of the thicker ones keeps a sweaty thumb where it belongs. Designed by SF3DPrints and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by SF3DPrints

A hook that hangs over the top of a door - no screws, no drilling, nothing to fix to the wall. 2.7" wide and 4.3" tall, about 13 g of plastic. Shown as a render of the printable model, not a photograph.

Design by blunt

A Saint Bernard sitting with its head up, cut into flat low-poly planes that read as fur from a distance and catch the light in a silk or metallic filament. About five inches deep, printed as one piece. The picture is a render of the printable model, not a photograph of a finished print.

Design by Creaitivity Studio

A rail that a CD jewel case stands in, ribbed along its length so the case leans back instead of sliding forward, on four short feet that keep the disc off the shelf. 149 mm wide and 30 mm tall - the width of a standard case, with a little room either side. Designed by ToToKia and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by ToToKia

A dalmatian sitting upright in low-poly facets, about five inches deep - a shelf or mantel piece that holds its shape from the side as well as the front. One piece, no supports. The picture is a render of the printable model, not a photograph of a finished print.

Design by Creaitivity Studio

A rose and its stem printed as one piece, so there is no assembly at the end: the petals spiral out of the bud and the stem runs down to a base that stands on a desk. The designer prints it as a classic print rather than vase mode, and suggests one perimeter and no infill with a transparent filament if you want the light to come through the petals. The page credits Lytta and RubixDragon for the roses it was built from - all three designers are named on this page. Printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by user_531694306

Five angels cut as openwork ornaments: flowing gowns, layered wings and a halo, each a little different and still of a piece with the others. No supports needed - print them flat, thread a string through the hole at the top and hang them where the light comes through the wings. The five together fill about nine inches square of plate. Designed by gahalam and printed under Creative Commons Public Domain (CC0 1.0). Shown as a render of the printable model, not a photograph.

Design by gahalam

A pick holder with four feet that stands on an amp or a desk: slanted slots take plectrums by the tip so they can be pulled out one at a time, and the block is 90 mm long, 28 mm wide and 12 mm tall. The slots are cut at an angle, which is what stops a pick sliding back down into the holder. Designed by gareth7562 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by gareth7562

A faceted tree on a weighted base, 173 mm tall: rings slide onto the branches, necklaces hang from them, and the low-poly planes catch the light instead of looking like a coat rack. Two pieces, no supports, and the base is wide enough that it does not tip when one branch is loaded. Designed by Beenox and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Beenox

Thirteen ornaments off two plates: eight hollow shapes with caps, two snowflakes, an eight-point star, a wreath and a set of digits, all about 50 mm across, printed from one spool of Galaxy filament so the colour shifts shade by shade through every bauble. Enough for a tree, or for a tree and the windows. Designed by 3D Crafts and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by 3D Crafts

A santa hat with the tip curling over: the brim is a raised band, the crown is domed and the tip hangs past the brim, so the shape reads from the side as well as the front. Each hat is 23.8 x 15.3 mm and 5.5 mm tall with a hole through the crown for a hook, and the plate prints six of them, which is three pairs. Shown as a render of the printable model, not a photograph.

Design by Ettore

A high-detail ice dragon with its wings spread and its head raised, about five and a half inches across - a display piece rather than a toy, with the scale and wing membrane holding up close. Printed exactly as the designer published it. The picture is a render of the printable model, not a photograph of a finished print.

Design by ScourgePrints

A lidded storage box for microscope slides: the box and its lid print as two pieces and close over the slides. 3.4" x 6.9" x 1.3" overall. Shown as a render of the printable model, not a photograph.

Design by Asky

A snowflake cut to sit over the top corner of a door frame, so the corner of a door is dressed for the season. It prints flat and reads well in one colour or in several - the designer's own photos show both. Designed by lindnjoe and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by lindnjoe

A ten-point star for the top of a Christmas tree. The plate carries two star faces with a mount and two pegs, so the star goes together without glue. Designed by hyperZ and printed under Creative Commons Public Domain, so it is free of conditions. Shown as a render of the printable model, not a photograph.

Design by hyperZ

A beaver balanced on its tail, built from an open voronoi lattice: solid from across the room, a web of struts up close, and it catches the light in a silk or metallic filament. One piece, and it stands on its own. Mosselini1 rebuilt the voronoi beaver and this is that remix. The picture is a render of the printable model, not a photograph of a finished print.

Design by Mosselini1

A bench holder that keeps dental drill bits upright, sorted and off the tray. 3.3" x 2.2" x 0.8", about 30 g of plastic. Shown as a render of the printable model, not a photograph.

Design by pain.killer.2

A spiral vase that stands on its own round base. Lloyd Tapper started from Tru!e's spiral flower pot and then fixed the thing that annoyed him - the vase slid around on the base - by adding a notch under the vase and turning the elevators on the base into cones, so the two move together when you pick the vase up. Both makers are credited on this page. Printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Lloyd Tapper

A vase drawn for spiral vase mode: one continuous wall spiralling up from the foot to the lip, so it prints in a single unbroken pass with no seam, and a light behind it shows the twist. Designed by elio196721 and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by elio196721

A Christmas tree with a twist - literally: the cone is a spiral, sculpted rather than stepped, so it catches the light from a window instead of sitting there like a green triangle. About 5.9 inches tall, which is table, shelf or desk size rather than tree size. Designed by Fprint3D and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by Fprint3D

Bauble hooks printed as a snap-off blister: a flat frame of S-hooks joined by 0.4 mm bridges, so you snap off as many as you need with your fingers and the rest stay in the frame, in the box, untangled. A couple of minutes of printing replaces the annual fight with a ball of wire hooks. The frame is about 5.3 by 1.7 inches and weighs 3 grams. Designed by mixardstudio.pl and printed under Creative Commons Public Domain (CC0 1.0). Shown as a render of the printable model, not a photograph.

Design by mixardstudio.pl

An autumn sign for a windowsill or a shelf: the word Hello stacked over Fall with a pumpkin alongside, flat on the back so it sits against a wall, and printed as separate pieces so the lettering and the pumpkin each take their own filament - the designer printed his in matte white, orange and brown. Designed by JMOS and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by JMOS

A tealight holder that only shows what it is once the candle is lit: a reindeer standing in a winter wood, cut as a silhouette inside a circular frame, with a notch behind it for a small LED candle. The light throws the trees and the reindeer onto the wall rather than just glowing. About 5.2 inches across. Designed by Walter 3D and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Walter 3D

A little town under snow that prints as one piece: rooftops, houses and trees drifting into each other, with holes modelled through the houses so a micro LED string can be threaded in and the windows light from inside. This is the designer's fixed-roof version, and davidkelly021 publishes a separate base for it with room for a battery pack. Printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by davidkelly021

A collie lying down with its head on its paws, cut into low-poly facets and about four inches long. One piece, no supports. The picture is a render of the printable model, not a photograph of a finished print.

Design by Creaitivity Studio

A dobermann sitting to attention in flat low-poly planes: ears up, chest forward, about four inches tall. One piece, no supports, and the facets suit a matte or metallic filament. The picture is a render of the printable model, not a photograph of a finished print.

Design by Creaitivity Studio

A pirate doubloon 45 mm across, with a skull and crossbones on the face and a beaded rim. The file prints fourteen on one plate, so it arrives as a small hoard - a treasure chest, a cake, a party favour or a handful for a costume. The picture is a render of the printable model, not a photograph of a finished print.

Design by Mike Coats

Eight napkin rings shaped like sea creatures - starfish, shells and fish - each holding a folded napkin on its side. About 3" across, printed flat in one colour or several. Shown as a render, not a photo.

Design by adnamantino

A dragon curled asleep on a bed of autumn leaves, small enough for a desk or a windowsill. Printed in a single colour with no AMS needed, so it comes off the plate ready to sit. The picture is a render of the printable model, not a photograph of a finished print.

Design by digidihey

A flat organizer that divides a kitchen drawer into compartments - it lies 2 mm deep, so it adds dividers without eating the depth of the drawer. 9.6" across, printed flat in one piece. Shown as a render, not a photo.

Design by Nix3D

A napkin holder with an open frame: a stack of serviettes sits in the base and the side wall holds them upright, so you can take one without the rest following. 6.3" long, printed in one piece. Shown as a render, not a photo.

Design by Jyffen

A mushroom table lamp: a voronoi-lattice cap over a chunky stem, printed as four parts (cap top, cap bottom, stem and a light-kit adapter) that assemble around a small lamp kit - the kit itself is not included. The cap is 9.4" across and the assembled lamp stands about 14" tall, roughly 587 g of plastic in all four parts. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Weso2976

Four wedding cutters with stamp inserts - the ring, the cake slice and two more - for biscuits at an engagement or a hen do. About 3" across each, and the same set cuts playdough for the small guests. Shown as a render, not a photo.

Design by Merilno3D

A single autumn leaf, 3.7" x 4.3" and 3 mm thick, printed flat in one colour. It sits under a mug as a coaster, or scatters across a shelf or a table for the season. Shown as a render of the printable model, not a photograph.

Design by 3D-Print-Bunker

A rest for a wooden spoon: the bowl sits in the cradle and the handle lies over the rim, so the drips land in the holder instead of the hob. 4.7" across, printed in one piece. Shown as a render, not a photo.

Design by Jirka108

A shelf that hangs under a shelf: it clips over the front edge of an existing board and gives you a second tier in the gap, for mugs, spice jars or a router. 6.9" wide, printed in one piece. Shown as a render, not a photo.

Design by PanteraRuber

A holder that stands cutlery up in a drawer or on a counter, with slots for forks, knives and spoons and a low front so you can see what you are reaching for. 5.9" long, printed in one piece. Shown as a render, not a photo.

Design by Alex

An upright organizer for the utensils that live on the counter: compartments of different heights, a flat back to go against a wall, and a base wide enough that a ladle does not tip it. 8" long, printed in one piece. Shown as a render, not a photo.

Design by lunatiic

A fridge egg dispenser: eggs roll down a ramp and out of the front one at a time, so the oldest is always the next to come out. 9.7" long and holds a dozen, printed in three pieces - the ramp, the body and the front cup - with no supports. Shown as a render, not a photo.

Design by specialman

A kitchen roll holder with a weighted base: the disc takes sand or coins, so the roll stays put while you pull one sheet off with one hand. 9.1" tall, printed as a base and a post. Shown as a render, not a photo.

Design by MicahW3D

A dragon in a coiled pose, wings half-open and tail curling round to its head - a display piece rather than a toy. 9.5" across and the biggest thing on the shelf, printed in one piece. Shown as a render, not a photo.

Design by mdesign

A chef's hat charm with a banded brim, tall enough to read at a glance on a keyring. Shown as a render, not a photo.

Design by Tim

Two clickers that look like lunch: a bao bun with its pleats, and half an avocado with the stone still in. Each is two printed halves that snap together over a switch, so the whole thing is the button. Pick the one you want - about 1.8" across. Shown as a render, not a photo.

Design by iNkosi3D

A bag peg that works like a clothes peg: two arms on a printed pin, so the ends you squeeze and the jaws are on opposite sides of the pivot, and squeezing opens the jaws. A disc on the upper arm turns inside a socket on the lower one, printed in place with a quarter of a millimetre of air round it - press the peg open and you can feel the pin move. Behind it one strip sweeps round and back to the other arm as a scroll you can see through, and that scroll is the spring: it closes the jaws and it is what you feel working when you squeeze. The mouth is a square-wave channel cut through both jaws at once, so the two sets of teeth come from the same cut and interlock - every tooth of one jaw stands in the hollow of the other - and along the outside of each arm, where a thumb goes, a row of sawteeth bites into the silhouette so the peg does not slip in your hand. It prints flat as one piece, no supports, nothing to assemble. PLA holds fine; PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

A fold-over bag clip in one piece, with nothing to assemble: two slim bars on a round hinge, and a hook at the far end that shuts them. Roll the bag's neck over, slide it in side-on between the bars, and press the hook home - the knob at the end of the curl rides over the upper bar's tip and drops into the groove cut behind it, so the clip is held shut by the hook and not by the moulding. Flex the curl back off the tip and it opens again. The hinge is a disc with a hole through it, so the clip hangs on a keyring or a cup hook when it is not on a bag. It prints flat as a single piece with no supports, and PLA holds fine while PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

Two hollow halves that screw together on a printed thread, plus two rings that turn either half into a stand. Fill it, twist it shut, and it is a box that looks like an egg; empty, it is an egg you can open again next year. About 1.8 inches tall, 31 g for the halves and the rings. Designed by Studio YBL - Tony Youngblood and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Studio YBL - Tony Youngblood

A set of gear examples for teaching - the gears and the pins that hold them, printed as one plate, each gear 80 mm across. Shown as a render of the printable model, not a photograph.

Design by osamutake