3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A hummingbird in flight framed by a teardrop outline: the bird sits inside the frame and joins it at the wing, with the hook tab above. Each is 27 x 41 mm and 2.3 mm thick, so the frame holds its shape rather than sagging, and the pair prints mirrored. Shown as a render of the printable model, not a photograph.

Design by Vulcain

A flip-flop outline, 48 x 18 mm and 2 mm thick, with the strap drawn as an open line across the sole and an eyelet at the toe for a hook. Long and narrow, so the pair swings rather than sitting flat against the ear. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by C4UStudio

The same heart twice, one a little larger than the other, each cut out of a single outline with its own hang hole - so one wears on a hook and the other takes a keyring. Both print flat together, about 28 x 29 mm and 2.4 mm thick. Shown as a render of the printable model, not a photograph.

Design by Brightbox

A hinged box for rings and earrings, 150 by 83 by 20 mm closed: a tray with compartments, a lid that shuts on printed hinges, and two pins that press in to hold the hinge line - four printed parts, no screws, no supports. Small enough for a wash bag and rigid enough to keep its shape. A remix of "Parametric hinged small parts box" by Billiam on Printables, which is CC BY 4.0, and designed by Ivan Chamberlain under Creative Commons Attribution 4.0 (CC BY 4.0) - both are credited. Shown as a render of the printable model, not a photograph.

Design by Ivan Chamberlain

A molar with a smiling face cut into it, in two sizes: 30 x 23 mm and 25 x 18 mm, with a hole at the crown for a hook. A gift for a dentist, a hygienist, or anyone who likes a tooth with a face on it. Sold as a pair. Shown as a render of the printable model, not a photograph.

Design by HaPeHu

A heart built from two nested outlines, so it reads as a heart from across a room and stays light on the ear. Each is 33 x 32.4 mm and 4.1 mm thick at the join, with a hole at the top for a hook, and the plate prints four hearts, which is two pairs. Shown as a render of the printable model, not a photograph.

Design by Fetter79

A pinecone geocache: a hollow cone with a screw-on cap and a loop at the top for a string or a length of wire, so it can hang in a branch. It prints in two pieces and neither needs supports. For a cache that lives outdoors, PETG keeps its shape in a hot car or a sunny hedge better than PLA. Designed by Soalar, who remixed it from Izak02's Pine cone cache - both makers are credited on this page. Printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Soalar

Six hearts on one plate: a large pair at 31 x 28 mm and two smaller pairs at 12 x 11 mm and 10 x 9 mm, each with a smiling face and a hole for a hook. Sold as a set of three pairs - the large hearts for everyday, the two small pairs for a second piercing or to give away. Shown as a render of the printable model, not a photograph.

Design by Merche

A sleigh and a reindeer, printed twice each: the sleigh has a curled runner and a seat, the reindeer has antlers and a tail, and both are 5.5 mm deep so they hold shape from the side. The plate holds four earrings, a pair of sleighs and a pair of reindeer, and they mix on one ear each way. Shown as a render of the printable model, not a photograph.

Design by tomo3D

Two sharpened pencils, 42 mm long and 11 mm across, with the point cut so the graphite reads as a separate tip - about 0.2 g of plastic each, which is light enough to forget they are on. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by Tinker Together. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Tinker Together

An arrow holder that takes up to twelve arrows, for shafts up to 11/32 of an inch across. One arrow or a dozen loaded on the same side, it stays upright, and it needs no supports; the designer printed his on an A1 mini. It is not a frugal print - the designer says so himself - so it is priced by what it weighs rather than by the pose. Designed by StickMan and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by StickMan

A kicking tee for rugby: a 120 mm base with a stem that stands the ball at the angle a kicker wants, so a conversion or a kick-off starts from the same place every time. 110 mm deep and 72 mm tall, printed as one piece with a wide foot that will not skate on wet grass. Designed by dhs and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by dhs

One continuous line draws a face in profile, cut out flat as an earring: 26 mm tall, 2 mm thick, with a hole at the top for a hook. Sold as a pair, mirrored so the two faces look at each other. Shown as a render of the printable model, not a photograph.

Design by Margen3d

A hot air balloon with its gores moulded in, the netting raised and a basket hanging under it on two lines, printed 1.9 mm thick. Each is 30 x 50 mm with a hole at the top of the envelope for a hook, and the pair prints together. Shown as a render of the printable model, not a photograph.

Design by ProtoEngineering

Eight citrus halves on one plate - orange, lime and lemon - each a 35 mm slice with a hole for a hook, so the set is four pairs or a bowl of citrus to rearrange. Printed flat in PLA with no supports and no colour changes: the segments are geometry, not paint. Designed by jdicerchio and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0); the parts are sold unaltered and this listing is offered under the same licence. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by jdicerchio

Christmas ornaments in the shape of balls, in three sizes - 40, 60 and 80 mm across - with the number of double ribs going up with the size: six on the smallest, ten in the middle and fourteen on the largest, each rib 3 mm wide. Each ball prints in two pieces, the ball and the bottom that closes it, and the designer prints that bottom with a support so the curve comes out clean and the ball sits tight against it. Designed by Jakub Lattenberg and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Jakub Lattenberg

A peg that holds a blanket down: the stem goes into sand or soft ground and the arm clamps the corner, so a windy afternoon does not take the picnic with it. Print in PLA or PETG, no supports; five come off one plate, about eight inches square. Designed by Ainon3Dprint and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Ainon3Dprint

A mirrored flourish - a curling stem with leaf-shaped tips - cut 2 mm thick, each about 24 x 36 mm with a hole at the end of the stem for a hook. The pair prints flat as one piece and lies along the ear rather than hanging off it. Shown as a render of the printable model, not a photograph.

Design by Vulcain

A ribbon of open spirals, 60 mm long and 25 mm across, printed upright so the turns come off the plate as clean as they look - nothing to sand between them. One earring fills the plate, so a pair is printed twice. Designed by Mike Olszak and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by Mike Olszak

A paw print with four toe pads and a deep heel pad, cut 2.3 mm thick so the pads stay proud of the outline instead of blurring into it. Each paw is 23 x 24.5 mm with a hole between the toes for a hook, and the pair is mirrored so the prints face the same way when they are worn. Shown as a render of the printable model, not a photograph.

Design by Slowpoke’s Workshop

A lid that presses onto an open drinks can and slides shut, keeping dust, wasps and debris out of a beer or a soda between sips. Two fits are on offer: the standard can, whose lid measures 1.4 by 1.9 inches, and a wider one at 1.5 by 2.4 inches for a fatter 16 oz rim. Each prints as a lid and its sliding cover, and the standard lid also comes in the designer's looser-fitting version for a can that runs tight. Designed by Tiger prints, who remixed EcoDad's Printables lid - both makers are credited on this page - and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Tiger prints

A pair of sunglasses with the arms and a bridge moulded in, printed 2.5 mm thick and 32 mm across, with a hole in each arm for a hook. They are a joke that prints properly: the lenses are open, so the shape holds at this size and reads at a glance. Shown as a render of the printable model, not a photograph.

Design by tomo3D

Two filigree horse heads, 45 mm by 28 mm and 2.5 mm thick, cut into openwork so they stay light enough to wear all day - about a gram and a half of plastic each. Printed exactly as the designer published them, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by C4UStudio. The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by C4UStudio

A hook that hangs over the top of a door - no screws, no drilling, nothing to fix to the wall. 2.7" wide and 4.3" tall, about 13 g of plastic. Shown as a render of the printable model, not a photograph.

Design by blunt

A can cap that opens the can as well: press it over the top of a standard 355 ml tab can and the drink is covered between sips, with the opener moulded into the same part. It prints in one piece in about forty minutes with no supports. Designed by BUD THE RETIRED PRINT GUY and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by BUD THE RETIRED PRINT GUY

A fish for the wall, cut flat: a simple fishing silhouette that the designer reshaped slightly to make it print cleanly. At 238 by 166 mm it is big enough to hold a wall on its own - a shed, a cabin, or the wall of somebody who would rather be fishing. Designed by MazziNiX and printed under Creative Commons Public Domain, so it is free of conditions. Shown as a render of the printable model, not a photograph.

Design by MazziNiX

A filigree arch: a curved band of scrollwork with the spaces cut right through, so it reads as lace from the front and sits like a crescent against the ear. Each is 26 x 34 mm and 2.3 mm thick with the hook tab at the top, and the pair is mirrored. Shown as a render of the printable model, not a photograph.

Design by Vulcain

A fidget cross charm whose arms spin in place, with the ring hole printed at the top for a chain or a split ring. Four sizes, 1.8" to 2.5" tall. Shown as a render of the printable model, not a photograph.

Design by BlackSheepStudio

A hook keeper that clips onto the rod handle and gives a lure somewhere to sit between casts, instead of swinging at the line. Three sizes, for rod handles of three diameters; the designer prints his in PETG and that is what the shop prints here, since this is a part that goes to the water. Designed by bambaxp and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by bambaxp

Five angels cut as openwork ornaments: flowing gowns, layered wings and a halo, each a little different and still of a piece with the others. No supports needed - print them flat, thread a string through the hole at the top and hang them where the light comes through the wings. The five together fill about nine inches square of plate. Designed by gahalam and printed under Creative Commons Public Domain (CC0 1.0). Shown as a render of the printable model, not a photograph.

Design by gahalam

Two flip flops printed as one piece, each with a raised strap and a toe post standing up through the sole, so they read as sandals rather than flat outlines. Each is about 30 mm long with a hole at the heel for a hook, and the pair comes off the plate together. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A snowball maker that presses an 80 mm ball and lets it go whole: two bowl halves on scissor arms, printed in place with no supports and no screws, plus a dowel for the hinge. The designer tested it through Alaskan winters; 0.12 mm layers keep the overhangs happy, and he publishes a heavier five-wall profile for hard-packed snow if you want this one built that way. Designed by Lawton Skaling and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Lawton Skaling

Thirteen ornaments off two plates: eight hollow shapes with caps, two snowflakes, an eight-point star, a wreath and a set of digits, all about 50 mm across, printed from one spool of Galaxy filament so the colour shifts shade by shade through every bauble. Enough for a tree, or for a tree and the windows. Designed by 3D Crafts and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by 3D Crafts

A headband with a horn and two ears, 205 mm across and 6 mm thick, so it sits flat on the head and prints in one piece on the plate with nothing to glue. The band is a loop rather than a rigid arc, so it grips a child's head and an adult's. Designed by Jakub Lattenberg and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Jakub Lattenberg

A santa hat with the tip curling over: the brim is a raised band, the crown is domed and the tip hangs past the brim, so the shape reads from the side as well as the front. Each hat is 23.8 x 15.3 mm and 5.5 mm tall with a hole through the crown for a hook, and the plate prints six of them, which is three pairs. Shown as a render of the printable model, not a photograph.

Design by Ettore

A lidded storage box for microscope slides: the box and its lid print as two pieces and close over the slides. 3.4" x 6.9" x 1.3" overall. Shown as a render of the printable model, not a photograph.

Design by Asky

A screw-top capsule for the small things that have to stay dry: matches, pills, a spare battery, a couple of picks. A loop on the cap hangs it from a backpack or a bike frame. Six sizes, 48 mm at the smallest and 128 mm at the largest, each printing as a container and its cap with no supports. The designer's optional TPU gasket - the part that makes it properly waterproof - is not something the shop prints, so as printed the thread keeps splashes and pocket lint out rather than a soaking. Designed by squinn and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by squinn

A snowflake cut to sit over the top corner of a door frame, so the corner of a door is dressed for the season. It prints flat and reads well in one colour or in several - the designer's own photos show both. Designed by lindnjoe and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by lindnjoe

A ten-point star for the top of a Christmas tree. The plate carries two star faces with a mount and two pegs, so the star goes together without glue. Designed by hyperZ and printed under Creative Commons Public Domain, so it is free of conditions. Shown as a render of the printable model, not a photograph.

Design by hyperZ

A headband in a soft wave, 157 mm across and printed in PETG the way its designer publishes it - PETG bends where PLA would snap, and a headband is a part that gets flexed every time it is worn. Designed by Elyse_ and released as Creative Commons Public Domain (CC0 1.0), so the prints may be sold with no condition attached. Shown as a render of the printable model, not a photograph.

Design by Elyse_

A Christmas tree with a twist - literally: the cone is a spiral, sculpted rather than stepped, so it catches the light from a window instead of sitting there like a green triangle. About 5.9 inches tall, which is table, shelf or desk size rather than tree size. Designed by Fprint3D and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by Fprint3D

Bauble hooks printed as a snap-off blister: a flat frame of S-hooks joined by 0.4 mm bridges, so you snap off as many as you need with your fingers and the rest stay in the frame, in the box, untangled. A couple of minutes of printing replaces the annual fight with a ball of wire hooks. The frame is about 5.3 by 1.7 inches and weighs 3 grams. Designed by mixardstudio.pl and printed under Creative Commons Public Domain (CC0 1.0). Shown as a render of the printable model, not a photograph.

Design by mixardstudio.pl

An abstract crucifix: the figure flows into the cross in one smooth line, pared down to the gesture rather than the detail. Three sizes in the one design family, 9.8", 9.3" and 8.6" at their longest - each sold on its own. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by 3dKingpin

A tealight holder that only shows what it is once the candle is lit: a reindeer standing in a winter wood, cut as a silhouette inside a circular frame, with a notch behind it for a small LED candle. The light throws the trees and the reindeer onto the wall rather than just glowing. About 5.2 inches across. Designed by Walter 3D and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Walter 3D

A little town under snow that prints as one piece: rooftops, houses and trees drifting into each other, with holes modelled through the houses so a micro LED string can be threaded in and the windows light from inside. This is the designer's fixed-roof version, and davidkelly021 publishes a separate base for it with room for a battery pack. Printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by davidkelly021

A race medal with a moulded ribbon and a numbered disc in the middle. The file holds first, second and third, so a set covers a whole podium for a school race or a party game. The picture is a render of the printable model, not a photograph of a finished print.

Design by Rodrigo Ferriz

A cross worn as a keychain: Jesus on the front, JESUS down the beam, and a molded loop at the top for a split ring. 3.9" tall and 2.4" across the arms, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Christ Art

Eight napkin rings shaped like sea creatures - starfish, shells and fish - each holding a folded napkin on its side. About 3" across, printed flat in one colour or several. Shown as a render, not a photo.

Design by adnamantino