3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

Showing 1-18 of 18 products

Filtered byFunctionalKitchenCraftStudyClear all
Snap-On Soda Can Lid and Opener3 photos
25% offBulk deal 4+
from $1.49Was: $1.99$1.34 each with 4+ in a $30 orderDetails

A lid that snaps onto a standard can and seals it up again between sips, and doubles as an opener when you slip it over the tab and tilt. It is the wider, support-free version, and it fits both the slim and the fat cans the designer built it around - European 202 cans, so if yours is a different can it is worth a quick measure. Light sanding on the slots is the only finishing it asks for.

Design by MakerShed

Snap-On Soda Can Lid and Opener

Puffer Jacket Pencil Holder4 photos
25% offBulk deal 4+
from $8.70Was: $11.60$7.83 each with 4+ in a $30 orderDetails

A pencil holder wearing a puffer jacket: quilted panels all round, with a zip, a collar and sleeves running up the sides. It holds pens, pencils, markers, brushes or small tools, and it is sturdy enough to be knocked about a desk. About two hours of printing, and the quilted panels take filament colours well - solid winter colours, pastels, or something loud.

Design by Sitsero

Puffer Jacket Pencil Holder

Printable Reading Ruler & Bookmark - 3D printed in the GTA4 photos
25% offClearance · only 3 left!
from $1.49Was: $1.99$1.34 each in a $30 orderDetails

A printable reading ruler with an integrated bookmark pointer. The pointer holds your line while you read and marks your place when the book closes - pick the length that suits your book.

Reading Ruler & Bookmark

Six Runner - Can holder:spinner, Low Filament use
25% offBulk deal 4+
from $13.89Was: $18.52$12.50 each with 4+ in a $30 orderDetails

A six-can holder that spins: six runners hold the cans and the base turns, and it uses very little filament for its size. Four pieces. Shown as a render, not a photo.

Design by JEP0405

Six Runner - Can holder:spinner, Low Filament use

Heart Stanley Straw Topper
25% offBulk deal 4+
from $1.49Was: $1.99$1.34 each with 4+ in a $30 orderDetails

A heart that sits on top of a straw, wide and low, catching the light as the cup moves. Shown as a render, not a photo.

Design by Morganja

Heart Stanley Straw Topper

bee stanley straw topper
25% offBulk deal 4+
from $1.49Was: $1.99$1.34 each with 4+ in a $30 orderDetails

A plump bee that clips onto the top of a straw, wings raised and its stripes cut deep enough to read across a table. It suits the 10 mm Stanley straws, is 1.6" by 1.5", and prints in one piece with no supports. Shown as a render, not a photo.

Design by Morganja

bee stanley straw topper

JEEP Stanley Straw Topper
25% offBulk deal 4+
from $2.00Was: $2.66$1.80 each with 4+ in a $30 orderDetails

A Jeep grille that rides on top of a straw, seven slots and all. Shown as a render, not a photo.

Design by Morganja

JEEP Stanley Straw Topper

Lips Stanley Straw Topper
25% offBulk deal 4+
from $2.34Was: $3.12$2.11 each with 4+ in a $30 orderDetails

A pair of lips that sits on top of a straw: the straw passes through the middle and the lips ride above the lid, catching the light as the cup moves. It suits the 10 mm Stanley straws, is 3.9" tall by 2.2" across, and prints in one piece. Shown as a render, not a photo.

Design by Morganja

Lips Stanley Straw Topper

Short Sword Bookmark
25% offBulk deal 4+
from $1.49Was: $1.99$1.34 each with 4+ in a $30 orderDetails

A short sword bookmark with its own sheath: the blade marks your page and the scabbard clips back over it. 5.7" long, printed flat, the two pieces together weighing about 8 g. Shown as a render of the printable model, not a photograph.

Design by Forged in Filament

Short Sword Bookmark

dog stanley straw topper
25% offBulk deal 4+
from $1.49Was: $1.99$1.34 each with 4+ in a $30 orderDetails

A dog's head that sits on top of a straw, ears up and nose forward. Shown as a render, not a photo.

Design by Morganja