3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A phone stand with a woodgrain surface that all but disappears behind the phone, so what you see is the screen standing on the desk rather than the stand holding it. A deep groove with a lipped front edge takes a phone upright for video calls or on its side for standBy and night-clock mode, and it fits anything from a small handset up to a Pro Max. Printed in PLA at 0.2 mm layers, 15% infill, no supports. It is designed for a wood-fill filament, which gives it the grain it is named for, though any matte colour prints just as well. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by M_LAB

Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A fried egg 45 mm across, the yolk standing proud of a wavy white, plus the small plug that snaps behind it into a shoe. Shown as a render of the printable model, not a photograph.

Design by Gyu.Lee

A hockey stick lying across a puck, with the round plug that pushes it into a clog: 48 mm across, 13 mm from the shoe to the top of the stick, printed as the charm and its plug together. Shown as a render of the printable model, not a photograph.

Design by hudsonch79

A crocodile in a straw hat and eyepatch, cut flat with four plugs behind it so it sits on top of a shoe: 33 x 29 mm. Shown as a render of the printable model, not a photograph.

Design by jstoner98

A soft-serve cone as a shoe charm: a 53 mm cone of waffle ridges under a swirl, with the plug behind it that pushes into a clog. Shown as a render of the printable model, not a photograph.

Design by Gyu.Lee

A dart-shaped glider printed as one piece: 24 cm nose to tail, 15.8 cm across the wings, 12 mm at its thickest, and about 7 g of plastic. It prints flat, so the whole plane lifts off the plate as one object with nothing to glue together - and being flat it takes a minute or two of plastic rather than a flight. A desk toy that looks like folded paper and will not crease, soak up a puddle or blow off a table. Designed by By_Menen and released into the public domain (CC0 1.0). The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by By_Menen

One pointed charm: an 18 mm cone on a flat base that presses into the hole of a clog, 13 mm across. Shown as a render of the printable model, not a photograph.

Design by ntalekt

A set of gear examples for teaching - the gears and the pins that hold them, printed as one plate, each gear 80 mm across. Shown as a render of the printable model, not a photograph.

Design by osamutake

A scoop for filling a bird feeder, a seed bag or a bucket, with a lip at the front that gets under the seed and a handle long enough to keep a glove on. It is a tool rather than a gadget: one piece, no moving parts, and it holds enough that filling a feeder takes two scoops instead of ten. 35 grams of plastic. Designed by halunke55 and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by halunke55

Two hexagonal mesh pockets angled into each other, so a pair of shoes sits heel-down without one resting on the other. 220 mm wide, 165 mm tall and 130 mm deep, printed as one piece. Remixed by ThatGuy123568 from jordi_id7's original Shoe organizer on Thingiverse. Shown as a render of the printable model, not a photograph.

Design by ThatGuy123568

A jitterbug mechanism: a foldable polyhedron in print-in-place segments that flips inside out when you squeeze it. One is about 1.8" x 1.6", and printed as one piece there is nothing to assemble. Sold as one jitterbug - the plate in the picture prints four. Shown as a render of the printable model, not a photograph.

Design by osamutake

A saddle that pins a length of half-inch PVC pipe flat to a wall or a ceiling: an arch over the pipe with a screw hole at each end, so the pipe is held at the fixings rather than resting in a clip that lets it slide. The designer made it to run a porch mister system along the back of a house, which is exactly the job - long runs of pipe that have to stay level and stay put. About 2.2 inches long, four screws (not included), and 7 grams of plastic each. Designed by FanForgeGifts, LLC and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by FanForgeGifts, LLC

A V-plow that clamps over the front of a clog: two mirrored blades, 118 mm long and 58 mm high, one for each shoe, that push snow aside as you walk. Shown as a render of the printable model, not a photograph.

Design by OVERTUREFilament

A 3-digit combination padlock as a kit card: every part prints flat, mounted on the card, and snaps off it. 4.5" x 3" and about 14 g with the card. Shown as a render of the printable model, not a photograph.

Design by LoboCNC

A short sword bookmark with its own sheath: the blade marks your page and the scabbard clips back over it. 5.7" long, printed flat, the two pieces together weighing about 8 g. Shown as a render of the printable model, not a photograph.

Design by Forged in Filament

Hooks that hold a stem where you want it: one end slips over a cane or a bamboo stake and the other curves round the plant, so a heavy tomato truss or a flopping dahlia stays up without twine. The set covers several shapes for different jobs - a hook, a double hook, a stake ring - and they go on and come off without disturbing the roots. The set is about 100 grams. Designed by Mr Random and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Mr Random

A bulldozer blade for a clog, with a toothed cutting edge and the brackets that hold it on: 81 mm across and 60 mm high, sold as a pair, one for each shoe. Shown as a render of the printable model, not a photograph.

Design by HazEyedeas

A small desk novelty in two parts, 2.5" x 2.6" x 0.8", printed as one plate. Shown as a render of the printable model, not a photograph.

Design by LoboCNC

A rack that stands petri dishes upright to drain or to sit on a shelf. 2.9" x 4.5" x 2.5". Shown as a render of the printable model, not a photograph.

Design by Clément Vasseneix

Two layered Christmas trees, 33 mm tall, each with a loop at the top for a hook - a few flat layers stacked into a tree, so they read as a tree from the front and none of it is a support to remove. Designed by instintkiller and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The "+ hooks" option arrives with the metal hooks fitted; the plain one is the printed plastic on its own. Shown as a render of the printable model, not a photograph.

Design by instintkiller

A rack that holds laboratory test tubes upside down so they drain and dry: 185 mm x 110 mm x 75 mm. Shown as a render of the printable model, not a photograph.

Design by jakub.fousek97

A clip for holding a vegetable plant to its stick - two arms that open over the stem and grip a cane, so nothing has to be tied and nothing cuts into the plant as it thickens. Print it in PETG rather than PLA, which is what gives it the flex to open and close without cracking. About an inch across and all of 2 grams, so a whole row costs a few cents of filament. Designed by Andreas_L and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Andreas_L

Three stick figures in fighting poses, each one holding your pencil where it would hold a weapon: an archer drawing a pencil like a bow, a spearman resting on a long one, and a sniper kneeling with one as a rifle. The archer takes short pencils of about 8 to 9 cm, the other two take ordinary 10 to 16 cm ones. Sold as the set of three. Designed by Gekko and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Gekko

An Easter egg in two halves that spiral into each other: you twist one into the other and the spiral holds, so the egg is a toy as much as an ornament, and it comes apart again. Sold as the two-part egg. Designed by Jakub Lattenberg and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Jakub Lattenberg

A taiko drummer whose drum is the holder: the hollow drum takes cotton swabs, and the figure's hands hold one snapped in half as a pair of drumsticks. Four printed parts - base, figure, drum and the rack behind him - and the drumsticks take a touch of glue to stay put, as the designer's own notes say. Sold as the set. Designed by Benji and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Benji

Two strands twisted around each other into a pen stand: a double helix about 22 cm tall on a 14 cm square base, printed in one piece with nothing to assemble. Pens drop into the gaps between the rungs and lean out along the twist, so a handful of them fan apart instead of clumping together in a cup - and the base is wide enough that a full stand does not tip. Empty, it is a desk ornament rather than a mug with pens in it, which is most of what a pen holder does all day. Printed in PLA at a 0.2 mm layer, about 34 g of plastic. Designed by AndreUser and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by AndreUser

A seed-starting tray built to sit under a tower hydroponic system: the seedlings germinate in the station while the tower is already running, so a crop goes in the moment the last one comes out. The tray holds the plugs and drains, and it stacks with the tower's own fittings. About ten by seven inches and 249 grams. Designed by Valera Perinski and printed under Creative Commons Public Domain (CC0 1.0). Shown as a render of the printable model, not a photograph.

Design by Valera Perinski

A soap dish shaped like a leaf, with the veins textured into the face. The file carries two bodies - a flat textured dish and a deeper one - and both are printed, so you get the pair and can keep the shallow one for a sponge. Designed by Fiteropp and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Fiteropp

A dinosaur cut into interlocking jigsaw pieces and sold as the whole set: twelve chunky pieces, printed flat in PLA, that push together into the animal and come apart again. Two editions, cut differently from the same artwork - Adult and Kid, with the Kid edition's tabs cut larger for smaller hands. Both print as a set with no supports and nothing to glue, and the loose pieces store as the shape they make. The Adult set is about 322 g of plastic and the Kid set about 352 g, so each one is a multi-plate print rather than an afternoon. Designed by oymate and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by oymate

Four feather shapes, each printed twice so every design makes a mirrored pair: 60 mm long, 2 mm thick, with the barbs cut through so the feather is an outline and the quill shows. Printed flat with no supports. The plate holds all eight earrings - the whole set of four pairs - and they come in one colour. Shown as a render of the printable model, not a photograph.

Design by KameleonForge

A blank topper that sits on a 40 oz Stanley cup lid, flat and smooth, so it is a base for whatever goes on top: the designer's own page explains how to add text to it in Bambu Studio, choosing the font and the size and then the colour of the topper and of the writing separately. Sold blank, exactly as published. Designed by Picture_it and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Picture_it

A small square gift box, about 60 mm across and 50 mm deep, with a lid that sits a little proud on purpose so it lifts off easily. The bow and the little tree decoration print as separate pieces, so the box can be used plain or dressed up - all four pieces come as the set, and there is room inside for a ring, a pair of earrings or a few chocolates. Designed by Lunavixen and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Lunavixen

A modular hydroponic tower printed as twelve parts: a base, the column that stacks, five growing cups and the plates that close the sides. The column is 220 mm across and 128 mm tall, each cup 55 mm. The modules come apart, so a tower can be built one section at a time and taken down again. Shown as a render of the printable model, not a photograph.

Design by user_139533078

A round spider web in a ring, with every strand cut through so the web is open and a spider sits in the middle of it. Each is about 44 x 48 mm and 2.2 mm thick, with a loop at the top for a hook, and both webs print together as one piece. Shown as a render of the printable model, not a photograph.

Design by tomo3D

Plant markers with the crop cut into them rather than written on: a row of fifteen vegetables and herbs, each with its own little icon above the word, driven into the bed so a row is labelled from the path. The designer's set also comes in French and German; this listing is the English fifteen. Each stake is about 5.9 inches long, and the set is 135 grams. Designed by Mack Stuff and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Mack Stuff

A rose for the top of a 40 oz Stanley cup lid: the bloom prints standing up on the topper, so a plain cup gets a flower on it with nothing to glue in place. It fits the 40 oz lid. Designed by speedster, who remixed Picture_it's blank Stanley lid topper - both makers are credited on this page and both licences are recorded beside the file. Printed under Creative Commons Attribution 4.0 (CC BY 4.0); the topper it is built on is CC BY-SA 4.0, and the print is sold unaltered. Shown as a render of the printable model, not a photograph.

Design by speedster

A three-part seed germinator - base, insert and lid - 4.5" x 5.5" and 20 mm deep, printed in whatever colour you pick. Shown as a render of the printable model, not a photograph.

Design by 3dmonios

A bird feeder shaped like a little house that hangs a fat ball under its own roof: two vertical holes take screws if it is going on a fence, two horizontal ones take a cord if it is going round a tree, so it can be fixed where a feeder normally cannot. The roof keeps the rain off and the ball hangs clear of the sides, which is what stops a fat ball going mouldy. About seven inches wide and 155 grams. Designed by Phio and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Phio

An egg with a door in it: the front opens and shuts on a hinge printed in place, so the little house egg can be opened as often as you like - the designer notes the first opening needs a gentle pull to snap the hinge free. Printed in the flat-bottomed version the designer supplies, so it stands. Designed by AcmeArt and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by AcmeArt

A medal rack: two upright spines joined to a flat back plate, with a hooked arm either side of each spine so medals hang in a row instead of sliding into a heap, and the back takes a screw or a strip of tape. About 9.5 inches wide - a whole season of races hangs off it. Designed by donnkey - a remix, in their words, of Alan Břuska's "Věšák na medaile - Medal hanger" on Printables - and printed under CC0. Shown as a render of the printable model, not a photograph.

Design by donnkey

A print-in-place bag clip: the hinge prints shut and then works, so there are no pins and nothing to assemble. 3.2" long, 1.2" wide. Shown as a render of the printable model, not a photograph.

Design by printerforge

A heart with a knitted texture - cable rows and ribs moulded into both faces - printed as one piece so it flexes in the hand: the segments print in place with a clearance between them, and nothing has to be assembled. About 3 inches across, which sits on a desk or in a gift box. Designed by HistoricalPiecesandMore and released under CC0. Shown as a render of the printable model, not a photograph.

Design by HistoricalPiecesandMore

A snowman in two printed pieces: a body with print-in-place joints for the arms, and a head that hangs on its own link so it swings independently as the earring moves. Each is about 30 mm tall, prints flat with no supports, and a pair is two snowmen. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A daisy with eight rounded petals and a raised centre, 35.6 mm across and 3 mm thick, printed with a matching stud so the flower sits on a post rather than dangling from a hook. The plate holds four flowers and four studs, which is two pairs; a pair is a flower and a stud for each ear. Shown as a render of the printable model, not a photograph.

Design by mhumphries1973

A dragon printed as a chain of flat segments joined by print-in-place hinges, so the body ripples along its length and lies straight when it hangs still. It is 59 mm nose to tail and 8 mm deep at the head, prints in one piece with no supports, and a pair is two dragons. Shown as a render of the printable model, not a photograph.

Design by tomo3D

A stand for a pair of drumsticks: a flat 195 mm base and a cradle post that takes them by the shaft, so they stand upright on a riser or a shelf instead of rolling off the kit. 238 mm across as printed, in two parts, with the post sitting in its seat on the base. Designed by jakub.fousek97 and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by jakub.fousek97

A reading guide that frames one line at a time so the page cannot swim: 5.1" x 1.4", 1.4 mm thick, light enough to leave in a book. Kept for kids learning to read, and for anyone whose attention slides down a full page. Shown as a render of the printable model, not a photograph.

Design by fgiancarelli