3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

Ballasted track sections for the Dragon Railway at 1/64: six straight lengths from 50 mm to 300 mm, each printed with its ballast shoulder moulded on, so a layout needs no loose gravel. The set is the six lengths the designer's plate holds, and his recommended minimum radius is 400 mm. The curved sections live in his second file, which prints a whole loop at once - that is a custom print rather than a shelf item, so ask for a quote and the shop will run the curves you need. Designed by RamBros and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by RamBros

A giraffe lying down with its neck folded back and its legs tucked - printed as a chain of segments, so it flops about when you pick it up. 6.5" long, and the eyes print as separate 8 mm pieces that go in after. Shown as a render, not a photo.

Design by SHF3D.

Labels for a kitchen garden: eleven vegetables and herbs - aubergine, basil, pumpkin, corn, parsley, leek, beetroot, chives, sunflower, spinach and zucchini - cut in relief so the word reads from the path and a season outside does not wear it away. Print at 0.2 mm with no supports. Each sign is about six inches wide on its own stake. Designed by Schenk and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Schenk

An articulated cat printed as one piece: the segments print with gaps between them, so it bends and curls in the hand and stands up to being carried around. The eyes are part of the same print. Designed by Xeraj, who remixed feketeimre's Flexi Cat - both makers are credited on this page - and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Xeraj

Bauble hooks printed as a snap-off blister: a flat frame of S-hooks joined by 0.4 mm bridges, so you snap off as many as you need with your fingers and the rest stay in the frame, in the box, untangled. A couple of minutes of printing replaces the annual fight with a ball of wire hooks. The frame is about 5.3 by 1.7 inches and weighs 3 grams. Designed by mixardstudio.pl and printed under Creative Commons Public Domain (CC0 1.0). Shown as a render of the printable model, not a photograph.

Design by mixardstudio.pl

A desk golf set in eleven printed pieces: a green you can rearrange piece by piece, a ball, a club and the furniture around it. About 3" a piece and 115 g of plastic for the set. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by SakiSale

A baby dragon that prints in one piece, with an articulated spine so the neck, wings and tail all bend and the whole thing can drape over a finger. It sits, curls and lies down, and needs no assembly and no supports. The picture is a render of the printable model, not a photograph of a finished print.

Design by Helios3D

An abstract crucifix: the figure flows into the cross in one smooth line, pared down to the gesture rather than the detail. Three sizes in the one design family, 9.8", 9.3" and 8.6" at their longest - each sold on its own. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by 3dKingpin

A bat whose wings are cut into linked segments, so they flex when it is handled and settle into a curve on a shelf - printed in one piece with every joint already free. 3.9" across the wingspan, about 7 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Tybob24

A cross worn as a keychain: Jesus on the front, JESUS down the beam, and a molded loop at the top for a split ring. 3.9" tall and 2.4" across the arms, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Christ Art

A bee feeder for the garden: a shallow dish with a landing grid so bees can drink without drowning in it. Fill it with sugar water and hang it or set it among the flowers. The picture is a render of the printable model, not a photograph of a finished print.

Design by DanyP86

A flat floral bookmark: one thin spray of three openwork blossoms and leaves that lies between the pages and reads against the paper, marking the page without thickening the book. 5.9 x 4.4" overall and 1.6 mm thin, printed flat in one piece in a few minutes. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Rankhispano

A flat organizer that divides a kitchen drawer into compartments - it lies 2 mm deep, so it adds dividers without eating the depth of the drawer. 9.6" across, printed flat in one piece. Shown as a render, not a photo.

Design by Nix3D

A crowned lion head with a loop at the top, about four inches tall - a pendant, a bag charm or a wall ornament, with the mane and crown cut deep enough to hold a highlight. One piece. The picture is a render of the printable model, not a photograph of a finished print.

Design by digidihey

A bookmark of a book with a coffee cup resting on the stack - flat, 3.7" tall, and thin enough that it does not mark the pages. Printed in one piece in about a minute. Shown as a render, not a photo.

Design by giessener

An anatomically correct spine in print-in-place articulated segments: it flexes, curls and holds whatever pose you leave it in, with no assembly. Full runs 10.5" top to tail; Mini is 6.1". Shown as a render of the printable model, not a photograph.

Design by IndigoRaptor

Four wedding cutters with stamp inserts - the ring, the cake slice and two more - for biscuits at an engagement or a hen do. About 3" across each, and the same set cuts playdough for the small guests. Shown as a render, not a photo.

Design by Merilno3D

A pencil cup wrapped in overlapping scales, so it reads as a little pinecone on the desk while holding a fistful of coloured pencils. 3.3" across and 3.1" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by impresionao

A rest for a wooden spoon: the bowl sits in the cradle and the handle lies over the rim, so the drips land in the holder instead of the hob. 4.7" across, printed in one piece. Shown as a render, not a photo.

Design by Jirka108

A holder that stands cutlery up in a drawer or on a counter, with slots for forks, knives and spoons and a low front so you can see what you are reaching for. 5.9" long, printed in one piece. Shown as a render, not a photo.

Design by Alex

An upright organizer for the utensils that live on the counter: compartments of different heights, a flat back to go against a wall, and a base wide enough that a ladle does not tip it. 8" long, printed in one piece. Shown as a render, not a photo.

Design by lunatiic

A fridge egg dispenser: eggs roll down a ramp and out of the front one at a time, so the oldest is always the next to come out. 9.7" long and holds a dozen, printed in three pieces - the ramp, the body and the front cup - with no supports. Shown as a render, not a photo.

Design by specialman

A 608 bearing that prints already assembled - the races, the balls and the cage all come off the plate as one piece, and it turns as soon as you break it free. 22 mm across, 7 mm thick, the size a fidget spinner or a skate wheel takes. Shown as a render, not a photo.

Design by Jerryie

A kitchen roll holder with a weighted base: the disc takes sand or coins, so the roll stays put while you pull one sheet off with one hand. 9.1" tall, printed as a base and a post. Shown as a render, not a photo.

Design by MicahW3D

A hexagonal fidget that prints flat in a few minutes and clicks between your fingers - no supports, no assembly, no settings to tune. 2.0" across. Shown as a render, not a photo.

Design by LangHjornArt

A baby hippo printed as a chain of articulated segments - stubby legs, a rounded snout and a tail - so it waddles about on a desk and settles into whatever pose you leave it in. 1.4" long, printed in one piece with no supports, in one colour or painted. Remixed by Joshuaisodd from Whitney Richmond's "Baby Hippo", sold under the same licence. Shown as a render, not a photo.

Design by Joshuaisodd

The flexi rex as a keychain: a chain of articulated segments with a loop through the tail, so it jingles and curls in a pocket. 2.5" long, printed in one piece with no supports. Shown as a render, not a photo.

Design by LukesWorkshopBuilds

A fat little frog printed as one piece, every joint already moving, so it sits on its haunches and waddles about when you nudge it. 1.5" across, in one colour or two. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by TinkerLink

The articulated dragon shrunk to pocket size: a chain of segments, a plated back and a tail that curls round to the head. 5.2" long, printed in one piece, and small enough to live in a bag. Shown as a render, not a photo.

Design by MeltyBits

A slug that ripples: a chain of segments under a soft brim, so it flows through your fingers and settles into a curl. Two sizes - 3.5" and 5.2" long - each printed in one piece with no supports. Remixed by Elite_1650 from Teque5's "Friendly Articulated Slug", sold under the same licence. Shown as a render, not a photo.

Design by Elite_1650

A little bear printed as a chain of flexing segments, with a loop through the top for a keyring - no supports anywhere. 2.2" tall, printed in one piece, and it wriggles when you hold it by the tail. Shown as a render, not a photo.

Design by TinkerLink

Ten layered fidget discs off one plate - each about 3" across, each with its own cut-through pattern and its own way of spinning and clicking. Pick the design you want; the picture on each chip is that disc. Shown as a render, not a photo.

Design by PenguinPrototypes

The full-size articulated dragon: plated spine, wings folded along its back, and a chain of joints from nose to tail so it coils around a monitor or a wrist. 7.0" long, printed in one piece with no supports. Shown as a render, not a photo.

Design by Freddie

A baby dragon sitting up with its little wings folded and its tail wrapped round its feet. 2.1" tall, printed in one piece with no supports, so it stands on a desk on its own. Shown as a render, not a photo.

Design by CLUCKWORKS3D

A fox printed as a chain of flexing segments - pointed ears, a bushy tail and a loop through the tail for a keyring - so it curls in a pocket and springs back. 4.2" nose to tail, printed in one piece. Shown as a render, not a photo.

Design by OrangeSs

A keyring that opens without a metal split ring, printed as one piece with nothing to assemble. The flat band is broken once, and across that break the two ends lap through the ring's own thickness - the socket keeps the lower half, the near end the upper, with a quarter of a millimetre of air between them - so the finished ring reads as one band with a hairline in it rather than two pieces butted together. What holds it shut is the gate's own end, narrowed to a tongue: the band's inner and outer edges step down either side of it, and the tongue carries a rounded bump underneath that sits in a seat cut into the socket. Flex the ring apart and the bump rides up its own rounded side, which is a detent and not friction; let go and it drops back in. The tongue is relieved with a round hole at its root, because that is where it bends when you press it up to open the ring. Flex it, thread your keys on, squeeze it shut. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

Varsity letters as keychains: a block letter with a stitched look, cut in relief and about 2.4" tall. Pick the letter you want - A to M are here, and each has a hole at the top for a keyring or a chain. Four or more of any mix come at the bulk rate. Shown as a render, not a photo.

Design by dominator334

A jumping spider, joints and all, with a loop through the top for a keyring - eight legs that fold under it and a body that moves when you hold the ring. 2.4" across, printed in one piece. Shown as a render, not a photo.

Design by Daann_ii

A jellyfish with a dome for a head and four little tentacles, printed in place on a round stand so it hovers on a desk. 2.3" across the stand, printed as one piece with the tentacles already free. Shown as a render, not a photo.

Design by slavko

A starfish printed in place, with five arms that already move on the plate and a face on top. 2.2" across, printed as one piece with no supports and nothing to assemble. Shown as a render, not a photo.

Design by slavko

A cat curled up as a charm, cut in flat relief so the shape reads at a glance on a keyring or a necklace. It prints flat with no supports and measures about 2.4" by 1.8". Shown as a render, not a photo.

Design by dominator334

A ball that screws into its own cage - the thread holds it, and it spins from one end to the other without ever coming free. 3.9" tall, printed in place in two pieces that come off the plate already assembled. Shown as a render, not a photo.

Design by Elaak

A dolphin that looks knitted and bends like a chain - stitches down the back, a fin and a tail that flex. 2.5" long, printed in one piece with a hole through the tail for a keyring. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by OrangeSs

A cactus that clicks: the body snaps onto a keyboard switch, so the whole cactus is the button and the click comes from the switch inside it. Four designs, sold one at a time - pick the cactus you want, about 1.3" tall, and it prints in two pieces that snap together without glue. Shown as a render, not a photo.

Design by UKSTL

An octopus with eight arms that trail behind it and a round head with two eyes on top - printed in one piece, no supports. 5.2" across the arms, and big enough to sit on a desk rather than in a pocket. Shown as a render, not a photo.

Design by Davis_County_Library

An orca printed in place: the body and its fins come off the plate as one piece that already moves. 2.4" long, with the eye patch and the white belly reading in black and white filament. Shown as a render, not a photo.

Design by slavko

A graduation cap and gown on a keyring: the mortarboard tilted over the gown, with a class year or a name across the front on the version the designer included for it. It hangs flat and reads clearly from a distance, which is what a keepsake for a graduate wants to do. Printed as one tag with the layered faces so the cap, the gown and the lettering each read separately. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Cardboard Junkie

Six horse silhouettes as keychains, each a different pose cut in relief and each with a hole at the top for a ring or a chain. Pick the horse you want - they print flat with no supports and measure about 2.4" by 1.5". Shown as a render, not a photo.

Design by dominator334