3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A spider printed flat as one piece with every leg already jointed, so it walks across a table when you nudge it and folds up small. 4.6" across, about 5 g of plastic. Shown as a render, not a photo.

Design by mieldeprot

A small dragon on a printed chain: plated back, a curled tail and a head that turns, all articulated from the plate. 6.1" long - long enough to drape over a monitor, small enough to carry. Shown as a render, not a photo.

Design by SHF3D.

A vortex vase whose wall spirals in one continuous swirl from base to off-centre mouth, so it looks like it is still turning. 5.4" tall over a 3" body, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by oakliz27

A slender dragon printed as a chain of spiky segments that flex and curl, with a horned head at one end - detailed all down its back and small enough to carry. 6.5" long, printed in one piece with every joint already free. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by CrissyCat

Twelve little pals off one plate, each about two inches across and printed as a single piece, with no supports and nothing to assemble. Pick the one you want - the size on each chip is that pal's own width by height, so a 2.8"x1.6" one is a different creature from a 2.0"x1.4". Shown as a render, not a photo.

Design by Apricity

The smallest flexi dragon the shop carries: a chunky little dragon of rounded segments that wiggle end to end, claws and all. 2.1" long and barely over a gram of plastic, printed in one piece - a natural market-table giveaway. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by CrissyCat

A little octopus printed as a chain of flexing segments, so its eight arms trail and curl behind it. 2.2" across, printed in one piece in a single colour or with the body and the arms in different ones. Shown as a render, not a photo.

Design by slavko

A monster printed as a chain of flexing segments - horns, a ridge of spines down its back and a tail that curls - so it stands up, slumps and wriggles. 3.9" tall, printed in one piece with no supports, in one colour or three. Shown as a render, not a photo.

Design by TinkerLink

A caterpillar printed as a chain of flexing segments with a face at one end, so it wriggles along your hand and curls up when you put it down. 6.7" long, printed in one piece, with no supports and no assembly. Shown as a render, not a photo.

Design by Pistachio

Four miniature garden tools - shovel, spade, pitchfork and rake - about 2.8" long, with the hafts and heads modelled properly rather than blobs. A set for a dollhouse garden, a terrarium or a plant shelf. Shown as a render, not a photo.

Design by Gekon3D

A lizard printed in one piece with no AMS and no supports - ridged back, splayed feet and a tail that curls, sitting flat wherever you put it. Three sizes: 1.7", 3.7" and 4.6" long, the smallest small enough for a keyring. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by AmandaRoos

A crocodile printed as a chain of flexing segments, grin and all, with a ridged back and a tail that whips about. Three sizes - 4.7", 5.6" and 7.5" long - each printed in one piece. Shown as a render, not a photo.

Design by SHF3D

A pill popper: drop a tablet in the cup, press the plunger and it crushes it under a lever instead of between two spoons. 4.2" long, printed in one piece, with a rounded base so it stands up. Shown as a render, not a photo.

Design by c4444

A screw toy for small hands: three chunky bolts with matching nuts, the caps they screw into and a long threaded rod - the plate is the whole set. The rod is 7.1" long, and every part is printed oversized so a toddler can get a grip on it. Shown as a render, not a photo.

Design by hyperZ

Nine flat dinosaur shapes, 1.6 mm thick and about 4" across, printed as a sheet you colour in and stand up. A pack for a rainy afternoon: colour them, cut them out, stick them to the fridge. Shown as a render, not a photo.

Design by Merilno3D

A penguin that comes apart into a stack of rings and goes back together again - the plate carries the body, four rings and the little caps, so it builds up and knocks down like a nesting toy. About 3.6" across the widest ring. Shown as a render, not a photo.

Design by katinkus

A rubber-band fly swatter gun: stretch the band, aim and let go, and it fires the swatter head across the room. Printed flat in five parts with no supports, about 5.2" long. Remixed by 123木头人 from uhltimate's original Fly Swatter Gun. Shown as a render, not a photo.

Design by 123木头人

A bunny printed as a chain of flexing segments with a carrot to go with it, so it curls up in your hand and springs straight again. The set prints as one plate - a 2.4" bunny and its carrot - and comes in a single colour or with the parts in different ones. Shown as a render, not a photo.

Design by TinkerTogether

A water dragon printed as a chain of flexing segments - ridges along the back, a finned tail, and no supports anywhere. 4.5" long, printed in one piece, and it settles into whatever shape you leave it in. Shown as a render, not a photo.

Design by TinkerTogether

A little alligator printed as a chain of flexing segments - ridged back, four stubby legs and a tail that swings - so it wriggles across the desk and settles into whatever shape you leave it in. 2.4" long, printed in one piece. Shown as a render, not a photo.

Design by Litolunar