3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A small desk novelty in two parts, 2.5" x 2.6" x 0.8", printed as one plate. Shown as a render of the printable model, not a photograph.

Design by LoboCNC

A rack that stands petri dishes upright to drain or to sit on a shelf. 2.9" x 4.5" x 2.5". Shown as a render of the printable model, not a photograph.

Design by Clément Vasseneix

A rack that holds laboratory test tubes upside down so they drain and dry: 185 mm x 110 mm x 75 mm. Shown as a render of the printable model, not a photograph.

Design by jakub.fousek97

A dinosaur cut into interlocking jigsaw pieces and sold as the whole set: twelve chunky pieces, printed flat in PLA, that push together into the animal and come apart again. Two editions, cut differently from the same artwork - Adult and Kid, with the Kid edition's tabs cut larger for smaller hands. Both print as a set with no supports and nothing to glue, and the loose pieces store as the shape they make. The Adult set is about 322 g of plastic and the Kid set about 352 g, so each one is a multi-plate print rather than an afternoon. Designed by oymate and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by oymate

A blank topper that sits on a 40 oz Stanley cup lid, flat and smooth, so it is a base for whatever goes on top: the designer's own page explains how to add text to it in Bambu Studio, choosing the font and the size and then the colour of the topper and of the writing separately. Sold blank, exactly as published. Designed by Picture_it and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Picture_it

A rose for the top of a 40 oz Stanley cup lid: the bloom prints standing up on the topper, so a plain cup gets a flower on it with nothing to glue in place. It fits the 40 oz lid. Designed by speedster, who remixed Picture_it's blank Stanley lid topper - both makers are credited on this page and both licences are recorded beside the file. Printed under Creative Commons Attribution 4.0 (CC BY 4.0); the topper it is built on is CC BY-SA 4.0, and the print is sold unaltered. Shown as a render of the printable model, not a photograph.

Design by speedster

A print-in-place bag clip: the hinge prints shut and then works, so there are no pins and nothing to assemble. 3.2" long, 1.2" wide. Shown as a render of the printable model, not a photograph.

Design by printerforge

A small star that spins: the arms are printed in place, so the star turns in the hand or on a desk, and at 28 mm across it is a pocket fidget rather than a desk toy. No AMS needed - it prints in one colour. Designed by Amanda Roos and printed under Creative Commons Public Domain; the designer asks only to be mentioned when it is sold, which this listing does. Shown as a render of the printable model, not a photograph.

Design by Amanda Roos

A print-in-place finger catapult: two halves that come off the plate already joined, with a sprung arm that flicks a small pellet across the desk. 3.1" long, about 13 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by somtru

A palm-sized egg shaker for small hands: 40 mm across and 57 mm tall, printed as one closed shell with the rattle sealed inside, so it shakes without anything coming loose that a toddler could get at. Two of them and a kitchen is a percussion section. Designed by craftygirl21 and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by craftygirl21

A dragon-scale egg that opens into two halves, one nested inside the other, with a printed shaker bead rattling in the middle: 47 mm across and 62 mm tall, an Easter egg that is a maraca as well as an ornament. The two halves print on one plate with the bead, and the file pauses at the colour change so the shell can come out in one colour and the dragon scale inside in another. Designed by ThrottleXdesign - a remix four links deep of the Original Dragon Egg by Studio YBL and tonyyoungblood - and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by ThrottleXdesign

A spider printed flat as one piece with every leg already jointed, so it walks across a table when you nudge it and folds up small. 4.6" across, about 5 g of plastic. Shown as a render, not a photo.

Design by mieldeprot

A small dragon on a printed chain: plated back, a curled tail and a head that turns, all articulated from the plate. 6.1" long - long enough to drape over a monitor, small enough to carry. Shown as a render, not a photo.

Design by SHF3D.

Eight bunny cookie cutters, each with a stamp insert - press the face and ears, cut the outline, bake. About 3" tall each, and the same set cuts playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A slender dragon printed as a chain of spiky segments that flex and curl, with a horned head at one end - detailed all down its back and small enough to carry. 6.5" long, printed in one piece with every joint already free. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by CrissyCat

Three sculpting tools with different ends - a flat blade, a point and a loop - for clay, fondant or plasticine. About 6" long each, printed flat in one piece, so they are light enough to work with for an hour. Shown as a render, not a photo.

Design by Chilly_275

Twelve little pals off one plate, each about two inches across and printed as a single piece, with no supports and nothing to assemble. Pick the one you want - the size on each chip is that pal's own width by height, so a 2.8"x1.6" one is a different creature from a 2.0"x1.4". Shown as a render, not a photo.

Design by Apricity

The smallest flexi dragon the shop carries: a chunky little dragon of rounded segments that wiggle end to end, claws and all. 2.1" long and barely over a gram of plastic, printed in one piece - a natural market-table giveaway. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by CrissyCat

A Christmas cookie stamp and its matching cutter: press the stamp into the dough and the outline cuts clean around it, so the icing has a line to follow. 3.1" across, printed as two pieces - stamp and cutter. Shown as a render, not a photo.

Design by P2T

Seven traditional Christmas shapes, each about 3" across, printed with a cutting rim and a handle you can press. Cut a whole tin of mixed biscuits from one set. Shown as a render, not a photo.

Design by The_echoscapes

A little octopus printed as a chain of flexing segments, so its eight arms trail and curl behind it. 2.2" across, printed in one piece in a single colour or with the body and the arms in different ones. Shown as a render, not a photo.

Design by slavko

Shims for levelling a cabinet, packing a hinge or shimming a door frame. One plate is four shims - 42 x 89 mm, one each at 1 mm, 2 mm, 3 mm and 5 mm thick - so you pick the thickness that squares the job up instead of stacking paper. Shown as a render, not a photo.

Design by 3dprinting

A monster printed as a chain of flexing segments - horns, a ridge of spines down its back and a tail that curls - so it stands up, slumps and wriggles. 3.9" tall, printed in one piece with no supports, in one colour or three. Shown as a render, not a photo.

Design by TinkerLink

A caterpillar printed as a chain of flexing segments with a face at one end, so it wriggles along your hand and curls up when you put it down. 6.7" long, printed in one piece, with no supports and no assembly. Shown as a render, not a photo.

Design by Pistachio

A lizard printed in one piece with no AMS and no supports - ridged back, splayed feet and a tail that curls, sitting flat wherever you put it. Three sizes: 1.7", 3.7" and 4.6" long, the smallest small enough for a keyring. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by AmandaRoos

A crocodile printed as a chain of flexing segments, grin and all, with a ridged back and a tail that whips about. Three sizes - 4.7", 5.6" and 7.5" long - each printed in one piece. Shown as a render, not a photo.

Design by SHF3D

A screw toy for small hands: three chunky bolts with matching nuts, the caps they screw into and a long threaded rod - the plate is the whole set. The rod is 7.1" long, and every part is printed oversized so a toddler can get a grip on it. Shown as a render, not a photo.

Design by hyperZ

A cupcake you can click: the frosting is the button, and it presses down with a proper click and springs back. Two sizes - 1.2" across for a keyring, 1.8" for a desk - each printed in one piece. Shown as a render, not a photo.

Design by MeltedMoose

Four bug cookie cutters with matching stamp inserts - cut the outline, press the details, bake. Each about 3" across, and the same set works for playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

Nine flat dinosaur shapes, 1.6 mm thick and about 4" across, printed as a sheet you colour in and stand up. A pack for a rainy afternoon: colour them, cut them out, stick them to the fridge. Shown as a render, not a photo.

Design by Merilno3D

A cap that turns a jar into a fruit washer: fill it, shake, and the water spins the berries clean instead of bruising them. The cap and its inner piece print together in one go - size L fits a standard wide jar. Shown as a render, not a photo.

Design by ValeraPerinski

A penguin that comes apart into a stack of rings and goes back together again - the plate carries the body, four rings and the little caps, so it builds up and knocks down like a nesting toy. About 3.6" across the widest ring. Shown as a render, not a photo.

Design by katinkus

A bit holder that clips to a Ryobi ONE+ battery: the mount takes the loose bits you are using and keeps them on the drill, so they travel with the tool rather than in a pocket. 2.1" long, printed in one piece. Shown as a render, not a photo.

Design by Terrain 6

A rubber-band fly swatter gun: stretch the band, aim and let go, and it fires the swatter head across the room. Printed flat in five parts with no supports, about 5.2" long. Remixed by 123木头人 from uhltimate's original Fly Swatter Gun. Shown as a render, not a photo.

Design by 123木头人

A bunny printed as a chain of flexing segments with a carrot to go with it, so it curls up in your hand and springs straight again. The set prints as one plate - a 2.4" bunny and its carrot - and comes in a single colour or with the parts in different ones. Shown as a render, not a photo.

Design by TinkerTogether

A water dragon printed as a chain of flexing segments - ridges along the back, a finned tail, and no supports anywhere. 4.5" long, printed in one piece, and it settles into whatever shape you leave it in. Shown as a render, not a photo.

Design by TinkerTogether

A bag clip shaped like a cat, with a spring jaw that holds a chip bag or a coffee pouch shut. 1.6" across, printed in place in one piece - the hinge comes off the plate already working. Shown as a render, not a photo.

Design by Muuurt

A little alligator printed as a chain of flexing segments - ridged back, four stubby legs and a tail that swings - so it wriggles across the desk and settles into whatever shape you leave it in. 2.4" long, printed in one piece. Shown as a render, not a photo.

Design by Litolunar

A free-standing kitchen roll holder: a weighted base and a post that takes a standard roll, so the paper comes off one-handed. 8.3" tall, printed in one piece - the stand-alone version needs no wall fixing. Shown as a render, not a photo.

Design by R3Designs