3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

An articulated cat printed as one piece: the segments print with gaps between them, so it bends and curls in the hand and stands up to being carried around. The eyes are part of the same print. Designed by Xeraj, who remixed feketeimre's Flexi Cat - both makers are credited on this page - and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Xeraj

An autumn sign for a windowsill or a shelf: the word Hello stacked over Fall with a pumpkin alongside, flat on the back so it sits against a wall, and printed as separate pieces so the lettering and the pumpkin each take their own filament - the designer printed his in matte white, orange and brown. Designed by JMOS and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by JMOS

A baby dragon that prints in one piece, with an articulated spine so the neck, wings and tail all bend and the whole thing can drape over a finger. It sits, curls and lies down, and needs no assembly and no supports. The picture is a render of the printable model, not a photograph of a finished print.

Design by Helios3D

An abstract crucifix: the figure flows into the cross in one smooth line, pared down to the gesture rather than the detail. Three sizes in the one design family, 9.8", 9.3" and 8.6" at their longest - each sold on its own. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by 3dKingpin

A collie lying down with its head on its paws, cut into low-poly facets and about four inches long. One piece, no supports. The picture is a render of the printable model, not a photograph of a finished print.

Design by Creaitivity Studio

A race medal with a moulded ribbon and a numbered disc in the middle. The file holds first, second and third, so a set covers a whole podium for a school race or a party game. The picture is a render of the printable model, not a photograph of a finished print.

Design by Rodrigo Ferriz

A bat whose wings are cut into linked segments, so they flex when it is handled and settle into a curve on a shelf - printed in one piece with every joint already free. 3.9" across the wingspan, about 7 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Tybob24

A dobermann sitting to attention in flat low-poly planes: ears up, chest forward, about four inches tall. One piece, no supports, and the facets suit a matte or metallic filament. The picture is a render of the printable model, not a photograph of a finished print.

Design by Creaitivity Studio

A pirate doubloon 45 mm across, with a skull and crossbones on the face and a beaded rim. The file prints fourteen on one plate, so it arrives as a small hoard - a treasure chest, a cake, a party favour or a handful for a costume. The picture is a render of the printable model, not a photograph of a finished print.

Design by Mike Coats

A cross worn as a keychain: Jesus on the front, JESUS down the beam, and a molded loop at the top for a split ring. 3.9" tall and 2.4" across the arms, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Christ Art

Eight napkin rings shaped like sea creatures - starfish, shells and fish - each holding a folded napkin on its side. About 3" across, printed flat in one colour or several. Shown as a render, not a photo.

Design by adnamantino

A dragon curled asleep on a bed of autumn leaves, small enough for a desk or a windowsill. Printed in a single colour with no AMS needed, so it comes off the plate ready to sit. The picture is a render of the printable model, not a photograph of a finished print.

Design by digidihey

A crowned lion head with a loop at the top, about four inches tall - a pendant, a bag charm or a wall ornament, with the mane and crown cut deep enough to hold a highlight. One piece. The picture is a render of the printable model, not a photograph of a finished print.

Design by digidihey

A napkin holder with an open frame: a stack of serviettes sits in the base and the side wall holds them upright, so you can take one without the rest following. 6.3" long, printed in one piece. Shown as a render, not a photo.

Design by Jyffen

An anatomically correct spine in print-in-place articulated segments: it flexes, curls and holds whatever pose you leave it in, with no assembly. Full runs 10.5" top to tail; Mini is 6.1". Shown as a render of the printable model, not a photograph.

Design by IndigoRaptor

A mushroom table lamp: a voronoi-lattice cap over a chunky stem, printed as four parts (cap top, cap bottom, stem and a light-kit adapter) that assemble around a small lamp kit - the kit itself is not included. The cap is 9.4" across and the assembled lamp stands about 14" tall, roughly 587 g of plastic in all four parts. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Weso2976

A single autumn leaf, 3.7" x 4.3" and 3 mm thick, printed flat in one colour. It sits under a mug as a coaster, or scatters across a shelf or a table for the season. Shown as a render of the printable model, not a photograph.

Design by 3D-Print-Bunker

A shelf that hangs under a shelf: it clips over the front edge of an existing board and gives you a second tier in the gap, for mugs, spice jars or a router. 6.9" wide, printed in one piece. Shown as a render, not a photo.

Design by PanteraRuber

A baby hippo printed as a chain of articulated segments - stubby legs, a rounded snout and a tail - so it waddles about on a desk and settles into whatever pose you leave it in. 1.4" long, printed in one piece with no supports, in one colour or painted. Remixed by Joshuaisodd from Whitney Richmond's "Baby Hippo", sold under the same licence. Shown as a render, not a photo.

Design by Joshuaisodd

The flexi rex as a keychain: a chain of articulated segments with a loop through the tail, so it jingles and curls in a pocket. 2.5" long, printed in one piece with no supports. Shown as a render, not a photo.

Design by LukesWorkshopBuilds

A dragon in a coiled pose, wings half-open and tail curling round to its head - a display piece rather than a toy. 9.5" across and the biggest thing on the shelf, printed in one piece. Shown as a render, not a photo.

Design by mdesign

A fat little frog printed as one piece, every joint already moving, so it sits on its haunches and waddles about when you nudge it. 1.5" across, in one colour or two. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by TinkerLink

The articulated dragon shrunk to pocket size: a chain of segments, a plated back and a tail that curls round to the head. 5.2" long, printed in one piece, and small enough to live in a bag. Shown as a render, not a photo.

Design by MeltyBits

A slug that ripples: a chain of segments under a soft brim, so it flows through your fingers and settles into a curl. Two sizes - 3.5" and 5.2" long - each printed in one piece with no supports. Remixed by Elite_1650 from Teque5's "Friendly Articulated Slug", sold under the same licence. Shown as a render, not a photo.

Design by Elite_1650

A little bear printed as a chain of flexing segments, with a loop through the top for a keyring - no supports anywhere. 2.2" tall, printed in one piece, and it wriggles when you hold it by the tail. Shown as a render, not a photo.

Design by TinkerLink

One little ghost, three sizes of it: Small is 35 mm tall, Medium 45 mm and Large 64 mm, so a shelf can gather a few rather than carry a loner. Each prints as a rounded little spectre with a friendly face and no supports. Every ghost is its own object on the plate, so no multi-colour printer is needed - print them in different colours and they arrive as a set. The small one disappears into a bowl by the door; the large still fits in a hand. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Amanda Roos

The full-size articulated dragon: plated spine, wings folded along its back, and a chain of joints from nose to tail so it coils around a monitor or a wrist. 7.0" long, printed in one piece with no supports. Shown as a render, not a photo.

Design by Freddie

A baby dragon sitting up with its little wings folded and its tail wrapped round its feet. 2.1" tall, printed in one piece with no supports, so it stands on a desk on its own. Shown as a render, not a photo.

Design by CLUCKWORKS3D

A fox printed as a chain of flexing segments - pointed ears, a bushy tail and a loop through the tail for a keyring - so it curls in a pocket and springs back. 4.2" nose to tail, printed in one piece. Shown as a render, not a photo.

Design by OrangeSs

A keyring that opens without a metal split ring, printed as one piece with nothing to assemble. The flat band is broken once, and across that break the two ends lap through the ring's own thickness - the socket keeps the lower half, the near end the upper, with a quarter of a millimetre of air between them - so the finished ring reads as one band with a hairline in it rather than two pieces butted together. What holds it shut is the gate's own end, narrowed to a tongue: the band's inner and outer edges step down either side of it, and the tongue carries a rounded bump underneath that sits in a seat cut into the socket. Flex the ring apart and the bump rides up its own rounded side, which is a detent and not friction; let go and it drops back in. The tongue is relieved with a round hole at its root, because that is where it bends when you press it up to open the ring. Flex it, thread your keys on, squeeze it shut. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

Varsity letters as keychains: a block letter with a stitched look, cut in relief and about 2.4" tall. Pick the letter you want - A to M are here, and each has a hole at the top for a keyring or a chain. Four or more of any mix come at the bulk rate. Shown as a render, not a photo.

Design by dominator334

A jumping spider, joints and all, with a loop through the top for a keyring - eight legs that fold under it and a body that moves when you hold the ring. 2.4" across, printed in one piece. Shown as a render, not a photo.

Design by Daann_ii

A jellyfish with a dome for a head and four little tentacles, printed in place on a round stand so it hovers on a desk. 2.3" across the stand, printed as one piece with the tentacles already free. Shown as a render, not a photo.

Design by slavko

A starfish printed in place, with five arms that already move on the plate and a face on top. 2.2" across, printed as one piece with no supports and nothing to assemble. Shown as a render, not a photo.

Design by slavko

A cat curled up as a charm, cut in flat relief so the shape reads at a glance on a keyring or a necklace. It prints flat with no supports and measures about 2.4" by 1.8". Shown as a render, not a photo.

Design by dominator334

A dolphin that looks knitted and bends like a chain - stitches down the back, a fin and a tail that flex. 2.5" long, printed in one piece with a hole through the tail for a keyring. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by OrangeSs

A vase with a wave running up its wall - a single spiralling surface, so the ridges catch the light differently as you walk past it. 180 mm tall, and shaped for dried flowers, pampas, feathers, or for nothing at all in a bare corner. It wants a dry arrangement rather than water. Print it in a silk or a matte filament and the waves do the rest of the work. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DueMakers

An octopus with eight arms that trail behind it and a round head with two eyes on top - printed in one piece, no supports. 5.2" across the arms, and big enough to sit on a desk rather than in a pocket. Shown as a render, not a photo.

Design by Davis_County_Library

An orca printed in place: the body and its fins come off the plate as one piece that already moves. 2.4" long, with the eye patch and the white belly reading in black and white filament. Shown as a render, not a photo.

Design by slavko

A graduation cap and gown on a keyring: the mortarboard tilted over the gown, with a class year or a name across the front on the version the designer included for it. It hangs flat and reads clearly from a distance, which is what a keepsake for a graduate wants to do. Printed as one tag with the layered faces so the cap, the gown and the lettering each read separately. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Cardboard Junkie

Six horse silhouettes as keychains, each a different pose cut in relief and each with a hole at the top for a ring or a chain. Pick the horse you want - they print flat with no supports and measure about 2.4" by 1.5". Shown as a render, not a photo.

Design by dominator334

An axolotl with its frilly gills out and a smile, printed in one piece with no AMS and no supports. 3.5" long, so it sits on a desk or rides along as a keyring charm. Shown as a render, not a photo.

Design by AmandaRoos

A little snake printed in one piece with no AMS and no supports, coiled so it sits up on its own tail. 2.5" long and about 2 g of plastic - a desk pet, or a whole plate of them for a market stall. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by AmandaRoos

A little cauldron with a lid full of bubbles, sized to sit over a battery tea light: the light comes up through the bubbles and the whole thing glows. It prints in two parts, the cauldron and its top, so the top can be a different colour from the pot - the designer printed the tops in plain white and let the tea light do the colour. About 70 to 77 mm tall once the two parts are together. Battery tea light only, never a real flame. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by DJH665

Take-away clickers: a burger, a box of fries and a drink cup, each printed as two halves that snap together over a switch, so the whole thing is the button. Pick the one you want - about 1.5" across - or four of any mix come at the bulk rate. Shown as a render, not a photo.

Design by iNkosi3D

A dinosaur that looks knitted rather than moulded - cable ribs down its back, a stitched belly and little knitted feet - printed as one piece. 3.0" long, and the stitch texture is the print itself, not a pattern painted on. Shown as a render, not a photo.

Design by hjs19

Christmas cone fidgets: a spiral cone that runs down through your fingers, and a Santa hat built the same way with its own spiral inside the brim. Pick the one you want - both print as a single piece and stand about 2.8" tall. Shown as a render, not a photo.

Design by Nerdherder

Two cats curled into a heart, cut in relief so the tails make the shape. Pick the fitting: the keychain has a ring hole, the charm is sized for a chain. It prints flat with no supports, about 1.9" by 2". Shown as a render, not a photo.

Design by dominator334