3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

Napkin rings for a Thanksgiving table, in four designs - an autumn leaf, a pumpkin, and two turkeys - that roll a napkin in a band and stand it up where a plate would. They print flat as a set and fold into the ring, so a table for eight is a short print rather than eight separate jobs. The set is about 68 grams. Designed by Lucholent Design and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Lucholent Design

A 1/64 scale GP60B diesel for the Dragon Railway: the body, the bogies and the small fittings, printed across five plates, about 191 g of plastic in the set. It is a layout model rather than a toy that survives a floor, and RamBros publishes an assembly manual and a video covering the parts it wants. Designed by RamBros and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by RamBros

A 1:20 pallet, 50 by 55 mm, for an RC forklift or a shelf of scale freight. It prints with no supports and, at two walls with solid bottom layers, comes out solid through the body. The proportions follow a UK-style pallet rather than a North American one. Designed by CippyO and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by CippyO

Two bats for the corner of a door frame at Halloween: one running along the top of the frame and a second spreading over the join. The pieces snap together - a little glue if a joint is loose - and a strip of tape on the back holds it where a frame is not square, which the designer added because his was not and says it is optional. Designed by jdicerchio and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by jdicerchio

A candy machine that turns a canning jar into a dispenser: a base that screws onto the jar's own lid ring, a knob and a printed pin, so no screw is needed anywhere. Fill the jar with sweets, fit the base, turn the knob and a few drop through. The designer also ships a stronger pin for silk PLA, and a second file for the narrower Hema store jar. Designed by carlbelcher and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by carlbelcher

A Halloween silhouette cut as one flat piece, 7" wide - the sort of thing you stand on a shelf or blu-tack to a window, and it reads from across a room. Printed flat in one piece, no supports. Shown as a render, not a photo.

Design by jwgnall

Four Halloween cutters - pumpkin, ghost, bat and the like - about 3" across each, printed with a cutting rim deep enough for biscuit dough or Play-Doh. One plate prints the set. Shown as a render, not a photo.

Design by Creaitivity Studio

A skeleton pinned flat and printed 3.7 mm thick, 6.9" tall - it hangs on a wall or a door and throws a proper outline, and it stacks flat in a box the other eleven months. Shown as a render, not a photo.

Design by TheModelAgency

A ghost with its hands over its face and a sheet that pools at the bottom, printed in one piece. Four sizes, from a 1.8" one for a windowsill to a 7.3" one that takes a shelf on its own. Shown as a render, not a photo.

Design by skuda3

A bat cut as one flat piece that folds along its wings, so it hangs from a thread and moves with the air rather than sitting rigid. 7.4" across, printed flat with no supports and a fraction under 10 g. Shown as a render, not a photo.

Design by M.Sima

A door corner for Halloween: a cat with a knife, cut to sit over the corner of a doorframe and be read from across the room. 7.9 by 7.8 inches and 5 mm thick, it prints flat in about an hour with no supports, and a 0.6 mm nozzle is an option the designer mentions for a chunkier line. Designed by H & R 3D and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), unchanged as published. Shown as a render of the printable model, not a photograph.

Design by H & R 3D

A shark in articulated segments, 110 mm from nose to tail, printed in one piece with the joints already free - it swims through the fingers and lies flat in a pocket. Printed exactly as its designer published it, under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0), designed by goatbuster. Shown as a render of the printable model, not a photograph.

Design by goatbuster

A bat with its wings wrapped forward, holding a tealight between them - the light spills out under the wings and throws the shape on the table. 5.5" tall, printed in one piece. Shown as a render, not a photo.

Design by Marlborke

A 1/64 scale tanker for the Dragon Railway: the tank, its chassis, walkway and bogies across three plates, about 98 g of plastic. The designer's own profile runs 0.08 mm layers, for the surface the model deserves. It runs on the Dragon Railway bogies and autocouplers, which are separate prints. Designed by RamBros and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by RamBros

A pumpkin cut into an open voronoi lattice, with a separate stem that sits in the top. The file also holds a second body with no base, if you would rather drop a tealight inside and let the shell glow through the gaps. Two pieces. The picture is a render of the printable model, not a photograph of a finished print.

Design by Mosselini1

A hand rising out of the ground with its fingers curled around a candle - the fingers grip an LED tealight, so the light comes out between them. 5.2" across, printed in one piece; a 46 mm version for a bigger candle is on file. Shown as a render, not a photo.

Design by PentillyCrafts

Ballasted track sections for the Dragon Railway at 1/64: six straight lengths from 50 mm to 300 mm, each printed with its ballast shoulder moulded on, so a layout needs no loose gravel. The set is the six lengths the designer's plate holds, and his recommended minimum radius is 400 mm. The curved sections live in his second file, which prints a whole loop at once - that is a custom print rather than a shelf item, so ask for a quote and the shop will run the curves you need. Designed by RamBros and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by RamBros

A lidded storage box for microscope slides: the box and its lid print as two pieces and close over the slides. 3.4" x 6.9" x 1.3" overall. Shown as a render of the printable model, not a photograph.

Design by Asky

A giraffe lying down with its neck folded back and its legs tucked - printed as a chain of segments, so it flops about when you pick it up. 6.5" long, and the eyes print as separate 8 mm pieces that go in after. Shown as a render, not a photo.

Design by SHF3D.

A spider that sits in the top corner of a door frame, printed flat and 4 mm thick so it reads as a silhouette against the wall. 6.9" tall, printed in one piece with no supports - a corner of tape holds it, and it comes down without a mark. Shown as a render, not a photo.

Design by Ned's Designs

A tower of ghost faces stacked one above the next, each turned a little further round than the last, about four and a half inches tall - a Halloween table piece that reads from across a room. One piece, no supports. The picture is a render of the printable model, not a photograph of a finished print.

Design by Thinkspace

An articulated cat printed as one piece: the segments print with gaps between them, so it bends and curls in the hand and stands up to being carried around. The eyes are part of the same print. Designed by Xeraj, who remixed feketeimre's Flexi Cat - both makers are credited on this page - and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Xeraj

A porch sign for the sweets bowl: PLEASE TAKE ONE in big raised letters with a little ghost beside it, on the plaque's own slot-in stand, which leans it back so it reads from the path. It prints in two colours with exactly one filament change - the plaque first, then the lettering, border and ghost on top in white, with the ghost's face cut through so the colour underneath shows. Plaque about six by four inches. Designed by rsw.io and printed under Creative Commons Public Domain (CC0 1.0). Shown as a render of the printable model, not a photograph.

Design by rsw.io

A baby dragon that prints in one piece, with an articulated spine so the neck, wings and tail all bend and the whole thing can drape over a finger. It sits, curls and lies down, and needs no assembly and no supports. The picture is a render of the printable model, not a photograph of a finished print.

Design by Helios3D

A hooded figure coming through a window: the robe, the reaching hands and the tattered edges are printed in two halves, one for each side of the glass, so from the path it looks as though something is passing through the pane. The halves clamp together with eight magnets, 10 mm across and 3 mm thick, four in each - buy the magnets before you print. About five inches tall, and the larger half takes supports. Designed by Pentilly Crafts and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Pentilly Crafts

A cat curled asleep inside a pumpkin, its back and tail proud of the shell - a Halloween piece about four inches wide that reads as one object until you are close enough to see the cat. Prints as one piece. The picture is a render of the printable model, not a photograph of a finished print.

Design by digidihey

A bat whose wings are cut into linked segments, so they flex when it is handled and settle into a curve on a shelf - printed in one piece with every joint already free. 3.9" across the wingspan, about 7 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Tybob24

A flat organizer that divides a kitchen drawer into compartments - it lies 2 mm deep, so it adds dividers without eating the depth of the drawer. 9.6" across, printed flat in one piece. Shown as a render, not a photo.

Design by Nix3D

An anatomically correct spine in print-in-place articulated segments: it flexes, curls and holds whatever pose you leave it in, with no assembly. Full runs 10.5" top to tail; Mini is 6.1". Shown as a render of the printable model, not a photograph.

Design by IndigoRaptor

Four wedding cutters with stamp inserts - the ring, the cake slice and two more - for biscuits at an engagement or a hen do. About 3" across each, and the same set cuts playdough for the small guests. Shown as a render, not a photo.

Design by Merilno3D

A rest for a wooden spoon: the bowl sits in the cradle and the handle lies over the rim, so the drips land in the holder instead of the hob. 4.7" across, printed in one piece. Shown as a render, not a photo.

Design by Jirka108

A holder that stands cutlery up in a drawer or on a counter, with slots for forks, knives and spoons and a low front so you can see what you are reaching for. 5.9" long, printed in one piece. Shown as a render, not a photo.

Design by Alex

An upright organizer for the utensils that live on the counter: compartments of different heights, a flat back to go against a wall, and a base wide enough that a ladle does not tip it. 8" long, printed in one piece. Shown as a render, not a photo.

Design by lunatiic

A fridge egg dispenser: eggs roll down a ramp and out of the front one at a time, so the oldest is always the next to come out. 9.7" long and holds a dozen, printed in three pieces - the ramp, the body and the front cup - with no supports. Shown as a render, not a photo.

Design by specialman

A kitchen roll holder with a weighted base: the disc takes sand or coins, so the roll stays put while you pull one sheet off with one hand. 9.1" tall, printed as a base and a post. Shown as a render, not a photo.

Design by MicahW3D

A baby hippo printed as a chain of articulated segments - stubby legs, a rounded snout and a tail - so it waddles about on a desk and settles into whatever pose you leave it in. 1.4" long, printed in one piece with no supports, in one colour or painted. Remixed by Joshuaisodd from Whitney Richmond's "Baby Hippo", sold under the same licence. Shown as a render, not a photo.

Design by Joshuaisodd

The flexi rex as a keychain: a chain of articulated segments with a loop through the tail, so it jingles and curls in a pocket. 2.5" long, printed in one piece with no supports. Shown as a render, not a photo.

Design by LukesWorkshopBuilds

A fat little frog printed as one piece, every joint already moving, so it sits on its haunches and waddles about when you nudge it. 1.5" across, in one colour or two. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by TinkerLink

The articulated dragon shrunk to pocket size: a chain of segments, a plated back and a tail that curls round to the head. 5.2" long, printed in one piece, and small enough to live in a bag. Shown as a render, not a photo.

Design by MeltyBits

A slug that ripples: a chain of segments under a soft brim, so it flows through your fingers and settles into a curl. Two sizes - 3.5" and 5.2" long - each printed in one piece with no supports. Remixed by Elite_1650 from Teque5's "Friendly Articulated Slug", sold under the same licence. Shown as a render, not a photo.

Design by Elite_1650

A little bear printed as a chain of flexing segments, with a loop through the top for a keyring - no supports anywhere. 2.2" tall, printed in one piece, and it wriggles when you hold it by the tail. Shown as a render, not a photo.

Design by TinkerLink

The full-size articulated dragon: plated spine, wings folded along its back, and a chain of joints from nose to tail so it coils around a monitor or a wrist. 7.0" long, printed in one piece with no supports. Shown as a render, not a photo.

Design by Freddie

A baby dragon sitting up with its little wings folded and its tail wrapped round its feet. 2.1" tall, printed in one piece with no supports, so it stands on a desk on its own. Shown as a render, not a photo.

Design by CLUCKWORKS3D

A fox printed as a chain of flexing segments - pointed ears, a bushy tail and a loop through the tail for a keyring - so it curls in a pocket and springs back. 4.2" nose to tail, printed in one piece. Shown as a render, not a photo.

Design by OrangeSs

A jumping spider, joints and all, with a loop through the top for a keyring - eight legs that fold under it and a body that moves when you hold the ring. 2.4" across, printed in one piece. Shown as a render, not a photo.

Design by Daann_ii

A jellyfish with a dome for a head and four little tentacles, printed in place on a round stand so it hovers on a desk. 2.3" across the stand, printed as one piece with the tentacles already free. Shown as a render, not a photo.

Design by slavko

A starfish printed in place, with five arms that already move on the plate and a face on top. 2.2" across, printed as one piece with no supports and nothing to assemble. Shown as a render, not a photo.

Design by slavko

A dolphin that looks knitted and bends like a chain - stitches down the back, a fin and a tail that flex. 2.5" long, printed in one piece with a hole through the tail for a keyring. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by OrangeSs