3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A lidded storage box for microscope slides: the box and its lid print as two pieces and close over the slides. 3.4" x 6.9" x 1.3" overall. Shown as a render of the printable model, not a photograph.

Design by Asky

A screw-top capsule for the small things that have to stay dry: matches, pills, a spare battery, a couple of picks. A loop on the cap hangs it from a backpack or a bike frame. Six sizes, 48 mm at the smallest and 128 mm at the largest, each printing as a container and its cap with no supports. The designer's optional TPU gasket - the part that makes it properly waterproof - is not something the shop prints, so as printed the thread keeps splashes and pocket lint out rather than a soaking. Designed by squinn and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by squinn

A bench holder that keeps dental drill bits upright, sorted and off the tray. 3.3" x 2.2" x 0.8", about 30 g of plastic. Shown as a render of the printable model, not a photograph.

Design by pain.killer.2

Eight napkin rings shaped like sea creatures - starfish, shells and fish - each holding a folded napkin on its side. About 3" across, printed flat in one colour or several. Shown as a render, not a photo.

Design by adnamantino

A flat organizer that divides a kitchen drawer into compartments - it lies 2 mm deep, so it adds dividers without eating the depth of the drawer. 9.6" across, printed flat in one piece. Shown as a render, not a photo.

Design by Nix3D

A napkin holder with an open frame: a stack of serviettes sits in the base and the side wall holds them upright, so you can take one without the rest following. 6.3" long, printed in one piece. Shown as a render, not a photo.

Design by Jyffen

Four wedding cutters with stamp inserts - the ring, the cake slice and two more - for biscuits at an engagement or a hen do. About 3" across each, and the same set cuts playdough for the small guests. Shown as a render, not a photo.

Design by Merilno3D

A rest for a wooden spoon: the bowl sits in the cradle and the handle lies over the rim, so the drips land in the holder instead of the hob. 4.7" across, printed in one piece. Shown as a render, not a photo.

Design by Jirka108

A holder that stands cutlery up in a drawer or on a counter, with slots for forks, knives and spoons and a low front so you can see what you are reaching for. 5.9" long, printed in one piece. Shown as a render, not a photo.

Design by Alex

An upright organizer for the utensils that live on the counter: compartments of different heights, a flat back to go against a wall, and a base wide enough that a ladle does not tip it. 8" long, printed in one piece. Shown as a render, not a photo.

Design by lunatiic

A fridge egg dispenser: eggs roll down a ramp and out of the front one at a time, so the oldest is always the next to come out. 9.7" long and holds a dozen, printed in three pieces - the ramp, the body and the front cup - with no supports. Shown as a render, not a photo.

Design by specialman

A 608 bearing that prints already assembled - the races, the balls and the cage all come off the plate as one piece, and it turns as soon as you break it free. 22 mm across, 7 mm thick, the size a fidget spinner or a skate wheel takes. Shown as a render, not a photo.

Design by Jerryie

A kitchen roll holder with a weighted base: the disc takes sand or coins, so the roll stays put while you pull one sheet off with one hand. 9.1" tall, printed as a base and a post. Shown as a render, not a photo.

Design by MicahW3D

A workshop set of ISO 4017 hex-head screws in M3, M4, M5, M6, M7, M8 and M10, each size on its own plate, so you print the sizes you need and keep a jar of spares. The whole set is seven plates and about 55 g of plastic; the M10 is 2.8" long. Shown as a render, not a photo.

Design by Jerryie

A chef's hat charm with a banded brim, tall enough to read at a glance on a keyring. Shown as a render, not a photo.

Design by Tim

Two clickers that look like lunch: a bao bun with its pleats, and half an avocado with the stone still in. Each is two printed halves that snap together over a switch, so the whole thing is the button. Pick the one you want - about 1.8" across. Shown as a render, not a photo.

Design by iNkosi3D

A bag peg that works like a clothes peg: two arms on a printed pin, so the ends you squeeze and the jaws are on opposite sides of the pivot, and squeezing opens the jaws. A disc on the upper arm turns inside a socket on the lower one, printed in place with a quarter of a millimetre of air round it - press the peg open and you can feel the pin move. Behind it one strip sweeps round and back to the other arm as a scroll you can see through, and that scroll is the spring: it closes the jaws and it is what you feel working when you squeeze. The mouth is a square-wave channel cut through both jaws at once, so the two sets of teeth come from the same cut and interlock - every tooth of one jaw stands in the hollow of the other - and along the outside of each arm, where a thumb goes, a row of sawteeth bites into the silhouette so the peg does not slip in your hand. It prints flat as one piece, no supports, nothing to assemble. PLA holds fine; PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

A fold-over bag clip in one piece, with nothing to assemble: two slim bars on a round hinge, and a hook at the far end that shuts them. Roll the bag's neck over, slide it in side-on between the bars, and press the hook home - the knob at the end of the curl rides over the upper bar's tip and drops into the groove cut behind it, so the clip is held shut by the hook and not by the moulding. Flex the curl back off the tip and it opens again. The hinge is a disc with a hole through it, so the clip hangs on a keyring or a cup hook when it is not on a bag. It prints flat as a single piece with no supports, and PLA holds fine while PETG survives the dishwasher and takes more flexing. The picture is a render of the printable model - real photographs of the print go up once the first batch comes off the printer.

Wet gloves dry upside down on six tapered, vented posts, over a 4x10 inch floor vent. A glove's cuff slides over a post so warm air from the register goes up through the post and through the glove, drying the inside as well as the out - which is the part that stays wet. The tray is a colander: a lip catches a dribble of water, and a grid of drain holes lets the air up and the water down, and each post drains through its own cup. Bottles and cups fit the posts just as the old stand's did. Sized to sit inside a 4 by 10 inch register, printed in one piece with no supports and nothing to assemble. The photo is a render of the printable model - real photos of the print go up once the first batch comes off the printer.

A set of gear examples for teaching - the gears and the pins that hold them, printed as one plate, each gear 80 mm across. Shown as a render of the printable model, not a photograph.

Design by osamutake

A short sword bookmark with its own sheath: the blade marks your page and the scabbard clips back over it. 5.7" long, printed flat, the two pieces together weighing about 8 g. Shown as a render of the printable model, not a photograph.

Design by Forged in Filament

A rack that stands petri dishes upright to drain or to sit on a shelf. 2.9" x 4.5" x 2.5". Shown as a render of the printable model, not a photograph.

Design by Clément Vasseneix

A set of fifteen Archimedean solids - the truncated and snub forms of the five platonic shapes - each 24 to 33 mm across and printed as one plate. A desk set for a maths classroom or a geometry shelf. Shown as a render of the printable model, not a photograph.

Design by mikan

A rack that holds laboratory test tubes upside down so they drain and dry: 185 mm x 110 mm x 75 mm. Shown as a render of the printable model, not a photograph.

Design by jakub.fousek97

The 2 to 9 times tables on one flat plate, 5" x 3.6" and 1.6 mm thick - a card that lives in a pencil case rather than on a screen. Shown as a render of the printable model, not a photograph.

Design by kot1199

A volcano model 5.9" across and 3.1" tall, printed as one piece - a desk piece, or the model for a school project on volcanoes. Shown as a render of the printable model, not a photograph.

Design by euro100xx

A blank topper that sits on a 40 oz Stanley cup lid, flat and smooth, so it is a base for whatever goes on top: the designer's own page explains how to add text to it in Bambu Studio, choosing the font and the size and then the colour of the topper and of the writing separately. Sold blank, exactly as published. Designed by Picture_it and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Picture_it

A rose for the top of a 40 oz Stanley cup lid: the bloom prints standing up on the topper, so a plain cup gets a flower on it with nothing to glue in place. It fits the 40 oz lid. Designed by speedster, who remixed Picture_it's blank Stanley lid topper - both makers are credited on this page and both licences are recorded beside the file. Printed under Creative Commons Attribution 4.0 (CC BY 4.0); the topper it is built on is CC BY-SA 4.0, and the print is sold unaltered. Shown as a render of the printable model, not a photograph.

Design by speedster

A print-in-place bag clip: the hinge prints shut and then works, so there are no pins and nothing to assemble. 3.2" long, 1.2" wide. Shown as a render of the printable model, not a photograph.

Design by printerforge

A stand for a pair of drumsticks: a flat 195 mm base and a cradle post that takes them by the shaft, so they stand upright on a riser or a shelf instead of rolling off the kit. 238 mm across as printed, in two parts, with the post sitting in its seat on the base. Designed by jakub.fousek97 and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by jakub.fousek97

A reading guide that frames one line at a time so the page cannot swim: 5.1" x 1.4", 1.4 mm thick, light enough to leave in a book. Kept for kids learning to read, and for anyone whose attention slides down a full page. Shown as a render of the printable model, not a photograph.

Design by fgiancarelli

An LP on the wall: a back plate with a shelf the cover stands on and two brackets that hold the record upright in front of it, so the sleeve and the disc are both on show. 218 by 214 mm and 187 mm deep, printed as one piece. Designed by LucMonnom and printed under Creative Commons Public Domain. Shown as a render of the printable model, not a photograph.

Design by LucMonnom

A strip that threads onto a guitar strap and holds a stack of picks, so a fresh one is within reach in the middle of a song: 100 mm long and 25 mm wide, printed in one piece. It sits on the strap rather than in a pocket, which is where picks go to be lost. Designed by willywidget and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by willywidget

A record sleeve stands on a ledge under a patterned back panel, and the ledge carries NOW PLAYING across its face in relief, so the record on the shelf is announced rather than guessed at. 200 mm wide and 159 mm tall - wide enough for a 12 inch sleeve - printed in one piece with no supports under the sign. Designed by Kosmok and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Kosmok

A table number: the digit cut as one flat plate inside an ornate oval frame, standing in a round base. Pick the number you need - every digit from 0 to 9 - and it arrives as the frame and its base, ready to slot together. About 5 inches tall, so it reads from across a room without sitting between two guests. Designed by swirly1007, who made the set for their daughter's wedding, and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by swirly1007

A golf tee with a ball sitting on its cup, printed as one piece - a desk trophy, a party favour or a cake pick as much as a tee. 2.3" tall, and barely a gram of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by LilÕJimbob

Eight bunny cookie cutters, each with a stamp insert - press the face and ears, cut the outline, bake. About 3" tall each, and the same set cuts playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

Three sculpting tools with different ends - a flat blade, a point and a loop - for clay, fondant or plasticine. About 6" long each, printed flat in one piece, so they are light enough to work with for an hour. Shown as a render, not a photo.

Design by Chilly_275

A Christmas cookie stamp and its matching cutter: press the stamp into the dough and the outline cuts clean around it, so the icing has a line to follow. 3.1" across, printed as two pieces - stamp and cutter. Shown as a render, not a photo.

Design by P2T

Seven traditional Christmas shapes, each about 3" across, printed with a cutting rim and a handle you can press. Cut a whole tin of mixed biscuits from one set. Shown as a render, not a photo.

Design by The_echoscapes

Shims for levelling a cabinet, packing a hinge or shimming a door frame. One plate is four shims - 42 x 89 mm, one each at 1 mm, 2 mm, 3 mm and 5 mm thick - so you pick the thickness that squares the job up instead of stacking paper. Shown as a render, not a photo.

Design by 3dprinting

A pill popper: drop a tablet in the cup, press the plunger and it crushes it under a lever instead of between two spoons. 4.2" long, printed in one piece, with a rounded base so it stands up. Shown as a render, not a photo.

Design by c4444

A cupcake you can click: the frosting is the button, and it presses down with a proper click and springs back. Two sizes - 1.2" across for a keyring, 1.8" for a desk - each printed in one piece. Shown as a render, not a photo.

Design by MeltedMoose

Four bug cookie cutters with matching stamp inserts - cut the outline, press the details, bake. Each about 3" across, and the same set works for playdough, which is what the designer made it for. Shown as a render, not a photo.

Design by Merilno3D

A cap that turns a jar into a fruit washer: fill it, shake, and the water spins the berries clean instead of bruising them. The cap and its inner piece print together in one go - size L fits a standard wide jar. Shown as a render, not a photo.

Design by ValeraPerinski

A hook remover with a forked end for backing a hook out and a flat end for pushing it through - the tool that means you do not put your fingers near the point. 4.8" long, printed flat in one piece. Shown as a render, not a photo.

Design by eclien

A bit holder that clips to a Ryobi ONE+ battery: the mount takes the loose bits you are using and keeps them on the drill, so they travel with the tool rather than in a pocket. 2.1" long, printed in one piece. Shown as a render, not a photo.

Design by Terrain 6

A napkin holder with a voronoi lattice for walls - it holds a stack of napkins and looks like something grown rather than built. 5.1" long, printed in one piece. Shown as a render, not a photo.

Design by IvanChamberlain