3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A phone stand with a woodgrain surface that all but disappears behind the phone, so what you see is the screen standing on the desk rather than the stand holding it. A deep groove with a lipped front edge takes a phone upright for video calls or on its side for standBy and night-clock mode, and it fits anything from a small handset up to a Pro Max. Printed in PLA at 0.2 mm layers, 15% infill, no supports. It is designed for a wood-fill filament, which gives it the grain it is named for, though any matte colour prints just as well. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by M_LAB

A set of gear examples for teaching - the gears and the pins that hold them, printed as one plate, each gear 80 mm across. Shown as a render of the printable model, not a photograph.

Design by osamutake

A scoop for filling a bird feeder, a seed bag or a bucket, with a lip at the front that gets under the seed and a handle long enough to keep a glove on. It is a tool rather than a gadget: one piece, no moving parts, and it holds enough that filling a feeder takes two scoops instead of ten. 35 grams of plastic. Designed by halunke55 and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by halunke55

A saddle that pins a length of half-inch PVC pipe flat to a wall or a ceiling: an arch over the pipe with a screw hole at each end, so the pipe is held at the fixings rather than resting in a clip that lets it slide. The designer made it to run a porch mister system along the back of a house, which is exactly the job - long runs of pipe that have to stay level and stay put. About 2.2 inches long, four screws (not included), and 7 grams of plastic each. Designed by FanForgeGifts, LLC and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by FanForgeGifts, LLC

A short sword bookmark with its own sheath: the blade marks your page and the scabbard clips back over it. 5.7" long, printed flat, the two pieces together weighing about 8 g. Shown as a render of the printable model, not a photograph.

Design by Forged in Filament

A set of fifteen Archimedean solids - the truncated and snub forms of the five platonic shapes - each 24 to 33 mm across and printed as one plate. A desk set for a maths classroom or a geometry shelf. Shown as a render of the printable model, not a photograph.

Design by mikan

Three stick figures in fighting poses, each one holding your pencil where it would hold a weapon: an archer drawing a pencil like a bow, a spearman resting on a long one, and a sniper kneeling with one as a rifle. The archer takes short pencils of about 8 to 9 cm, the other two take ordinary 10 to 16 cm ones. Sold as the set of three. Designed by Gekko and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by Gekko

The 2 to 9 times tables on one flat plate, 5" x 3.6" and 1.6 mm thick - a card that lives in a pencil case rather than on a screen. Shown as a render of the printable model, not a photograph.

Design by kot1199

A volcano model 5.9" across and 3.1" tall, printed as one piece - a desk piece, or the model for a school project on volcanoes. Shown as a render of the printable model, not a photograph.

Design by euro100xx

Two strands twisted around each other into a pen stand: a double helix about 22 cm tall on a 14 cm square base, printed in one piece with nothing to assemble. Pens drop into the gaps between the rungs and lean out along the twist, so a handful of them fan apart instead of clumping together in a cup - and the base is wide enough that a full stand does not tip. Empty, it is a desk ornament rather than a mug with pens in it, which is most of what a pen holder does all day. Printed in PLA at a 0.2 mm layer, about 34 g of plastic. Designed by AndreUser and printed under Creative Commons Attribution 4.0 (CC BY 4.0). The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by AndreUser

A bird feeder shaped like a little house that hangs a fat ball under its own roof: two vertical holes take screws if it is going on a fence, two horizontal ones take a cord if it is going round a tree, so it can be fixed where a feeder normally cannot. The roof keeps the rain off and the ball hangs clear of the sides, which is what stops a fat ball going mouldy. About seven inches wide and 155 grams. Designed by Phio and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Phio

A reading guide that frames one line at a time so the page cannot swim: 5.1" x 1.4", 1.4 mm thick, light enough to leave in a book. Kept for kids learning to read, and for anyone whose attention slides down a full page. Shown as a render of the printable model, not a photograph.

Design by fgiancarelli

A modular glasses stand: a round 143 mm base with a spindle, a post that carries two long arms, and a cradle that stacks on the spindle, so two pairs or a shelf-full can be kept upright and out of the way. The arms take frames by the bridge and the base is heavy enough not to tip when one pair comes off. Designed by Rockthered and printed under Creative Commons Attribution-ShareAlike 4.0 (CC BY-SA 4.0). Shown as a render of the printable model, not a photograph.

Design by Rockthered

A bookmark shaped like an alligator, with the jaw clipping over the page and the body lying in the gutter - so it marks the page and the line at once. 3.9" long, printed as a body and a jaw. Shown as a render, not a photo.

Design by 3dprinting

The Thinker, sitting on a plinth with his chin on his fist and a pair of glasses resting across his knee: 101 by 141 mm and 114 mm tall, printed in one piece as a desk glasses holder. The pose is what does the work - a pair sits in the crook of the arm and the knee, so it is always where it was put. Designed by Abz and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by Abz

A little hand that clips onto the page and points at the exact line you stopped on - so a bookmark marks where you are, not just which page. 2.8" long, printed flat with the fingers already free. Shown as a render, not a photo.

Design by helder.bernardo

An impossible passthrough wound as a spiral: the helical parts turn through each other and hold, printed in one piece. 2.8" tall, about 29 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A stackable glasses stand: a fin that the cradles slide onto, so the tower grows to whatever height the collection needs. The cradles come in three widths - 67, 77 and 87 mm - and each holds one pair nose-down by the bridge, which suits slim readers and deep sunglass frames alike. The plate prints a whole tower's worth of parts, 167 by 199 mm laid out as the designer arranges it. Designed by Badger Sound Forge and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by Badger Sound Forge

An impossible passthrough in pentagon form: the inner shape turns through the outer one and cannot come apart. 2.8" tall, about 31 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A golf tee with a ball sitting on its cup, printed as one piece - a desk trophy, a party favour or a cake pick as much as a tee. 2.3" tall, and barely a gram of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by LilÕJimbob

A small hook that sticks to a desk or a shelf edge with tape or a screw, for keys, headphones or a cable. 2.6" wide, printed in one piece with a flat back that sits flush. Shown as a render, not a photo.

Design by schiko

A mini golf hole for the desk: a printed course board with the hole and a rock surround, a club and a ball, all printed flat. 8.7" x 7.2", about 62 g of plastic for the set. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by MoltenPlastic3D

A pen holder clad in raised dragon scales, hexagonal all the way round, with a smooth inner cup for pens, pencils or brushes. 3.1" across and 4" tall, printed in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by 3DWoosh

A fidget web: a lattice of hinged segments that folds through itself and comes back again, printed as one piece with nothing to assemble. 3.7" across, about 28 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A B2 in flying-wing form that sits on top of a joystick - the shape slots over the stem and pegs in, so it turns with the stick. 5.5" across the wings, printed in one piece plus two pegs. Shown as a render, not a photo.

Design by DeanPrinting

A flat page marker with a fox carved in raised relief across its face - it slides over the page and the design reads against the paper. 9.4" long and 2.7 mm thin, printed flat in one piece. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by shadow.lune

A cone that passes through its own core and keeps going - a puzzle you can hold, printed in one piece with no assembly. 2.8" tall, about 19 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by BeninManc

A ruler that folds: nineteen 160 mm segments that hinge end to end, plus the two end caps, so it measures a room and then folds down to a pocket. The full set is 19 segments; the smaller option is the same design at 70 per cent, which is the one for a desk drawer. Shown as a render, not a photo.

Design by PenguinPrototypes

A top that keeps going: a heavy rim, a fine point and a printed handle to spin it between finger and thumb. 2.1" across, about 41 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by happybirthday

A hook remover with a forked end for backing a hook out and a flat end for pushing it through - the tool that means you do not put your fingers near the point. 4.8" long, printed flat in one piece. Shown as a render, not a photo.

Design by eclien

A beer crate for batteries, scaled down to sit on a shelf: stacked sides, a slotted top and a handle you can actually lift it by. Holds a row of AA or AAA cells - pick which, they are separate crates. About 2.7" long. Shown as a render, not a photo.

Design by JSBallpython

A thin blade for digging the lint out of a phone's charging port, with a hook at one end and a flat scraper at the other. 34 mm long and a fraction of a gram, so it prints three at a time in a minute - one for the desk, one for the car, one to lose. Shown as a render, not a photo.

Design by eclien