3D-printed products and 3MF downloads from Roxium in Burlington, Ontario

A butterfly cut from one flat plate, wings spread to about 9.5 inches across, with the wing veins and the row of spots opened right through so the wall colour shows in them. It hangs flat against a wall, a window frame or the back of a door, where a shelf ornament would not fit. Sold as the single printed piece. Designed by VK3DWorks and printed under Creative Commons Attribution 4.0 (CC BY 4.0). Shown as a render of the printable model, not a photograph.

Design by VK3DWorks

A reading guide that frames one line at a time so the page cannot swim: 5.1" x 1.4", 1.4 mm thick, light enough to leave in a book. Kept for kids learning to read, and for anyone whose attention slides down a full page. Shown as a render of the printable model, not a photograph.

Design by fgiancarelli

A tree-shaped photo frame: a heart in the middle and branches around it holding small photographs, with the plates that back them printed alongside so the pictures stay in without glue or tape. The designer scaled the pieces so the larger tree prints on one sheet, and suggests an acetate sheet in front of each photo to keep the dust off. Sold as the printed set. Designed by PediMR and printed under Creative Commons Attribution-NoDerivatives 4.0 (CC BY-ND 4.0). Shown as a render of the printable model, not a photograph.

Design by PediMR

A pair of racked display panels: a honeycomb grid and a mounting bracket that hold a row of pairs upright, so studs and hooks hang free instead of lying together. Assembled it is about 178 x 156 mm, prints flat in two pieces with no supports, and comes to about 40 g of plastic. Shown as a render of the printable model, not a photograph.

Design by thift88

A large arched tunnel for a vivarium: a rock-textured hide that a reptile or amphibian can walk through and sleep in. 7.9" long, about 256 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by VivariumVisions

A wolf howling at the moon, drawn as one low-poly silhouette: a single flat piece that hangs as wall art. 4.6" x 6.3", about 6 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

An owl silhouetted inside a circle, printed as one flat disc for the wall. 8.3" x 8.5", about 51 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by bigdobbo3D

Eight floral line-art pieces drawn as continuous lines: a set of wall decorations from 4" to 5.7" tall, about 60 g of plastic for all eight. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Astler

A stag head in faceted planes, printed as one flat piece - a low-poly wall hanging in a single colour. 5.7" x 6.2", about 4 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

A BMW E36 mid-drift, cut as a minimalist silhouette with the car sitting low and sideways. 7" x 5.4", about 7 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Kuba

A wolf in profile built from flat geometric planes: one piece, printed flat, for a wall or a desk stand. 7" x 4.3", about 5 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Peppino

An otter floating on its back, cut as a friendly 2D silhouette for a wall or a nursery shelf. 9.1" x 9.1", about 59 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Michel

A flower on a stem that stands on its own - the petals print as one piece with the stalk, so it needs no water and no vase. 3.9" tall, and the stem is a separate file if you want a different height. Shown as a render, not a photo.

Design by JarJar

A lionfish in chroma relief: fins and body modelled as stepped layers, so one print reads as several shades on the wall. 9.4" x 6.3", about 48 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by SuperBgr

A dragon egg with overlapping scales and a lid that lifts off, so it hides something small inside. 2.4" tall, printed in one piece - the shell and the lid come off the plate together. Shown as a render, not a photo.

Design by LLucas404

A cat sitting down, drawn in a few clean planes: a shelf ornament with a flat back and a simple, modern silhouette. 3.1" tall, about 11 g of plastic. The picture is a render of the printable model - real photographs of the print go up once the first one is made.

Design by Jo01

A dragon egg with scales cut over the whole shell and a lid that lifts off, so it hides something small. Three sizes: 1.4", 2.8" and 3.7" tall, the big one weighing about 50 g. Printed in one piece, lid and all. Shown as a render, not a photo.

Design by Type1Printing

Sixteen ring gauges from 15.4 mm to 27.6 mm across, printed flat on one plate so you can measure a finger properly instead of guessing. The whole set is about 6 g of plastic - print it once and keep it in a drawer. Shown as a render, not a photo.

Design by porkac

A sitting baby elephant with its trunk curled up and its ears out, printed in one piece with no supports. 2.4" tall, and about 9 g of plastic, so it sits on a shelf or a desk without a base. Shown as a render, not a photo.

Design by user_1541493983